Re: These dad burn ads!!

You guys are certainly an inexhaustable supply of knowledge. I've just been reading in more or less the side lines(since I joined) with only an occasional comment to make and the odd request for assistance. I've been gone for a few days and when I return my mail box has been inundated with mail. Going over most of them it seems that most of you have a problem with those advertisements that have been so boldly stuck on the top of the correspondence. Truly, I fail to see what irks you'se so much. We are here to read and learn from this are we not? It just seems like a very small inconvenience to have to put up with when we get so much in return. Lighten up ya'll the bottom line is always the "unholy" dollar. I feel it is no more annoying than having to go over all these emails that have piled up over the past few days. Even though it was my own doing for not sitting my email up to handle this event. What I'm trying to say is, "its the medium and its there to be exploited."
That's my opinion and I'm sticking to it! The content of the message is what matters is it not?

Sincerely
Wilfred Yellow
Double Eagle Marketing
===========================
Discover the Secrets to Wealth
Download your FREE copy of
"Soar With the Eagles,Share the Wealth" Booklet
visit: http://www.double-eagle-marketing.com/partners/WY1251
reply to: mailto:info@...
====================================================
Please visit:
http://www.freedownline.net/members/snookums681.html
You will not be disappointed!!
==============================================
http://www.themail.com/ref.htm?ref=1216320
==============================================

----- Original Message -----
From: Alan Marconett KM6VV
To: CAD_CAM_EDM_DRO@egroups.com
Sent: Sunday, September 03, 2000 5:12 AM
Subject: [CAD_CAM_EDM_DRO] Re:Gcode




My Groups | CAD_CAM_EDM_DRO Main Page | Start a new group!


Ballendo,

Thanks for the examples. I can see some uses now. I inscribed three
circles in three faces of cube, and generated code for it in VectorCAD.

(three circles 9/2/00 alm)
N05 F5
N10 G00 X0.000 Y2.000 Z3.500
N11 G19
N12 G03 Y2.000 Z3.500 J0.000 K-1.500
N13 G00 X3.500 Y2.000 Z4.000
N14 G17
N15 G03 X3.500 Y2.000 I-1.500 J0.000
N16 G00 X3.500 Y0.000 Z2.000
N17 G18
N18 G02 X3.500 Z2.000 I-1.500 K0.000
N19 G17

I added the G17/18/19. I get how it works now. Doesn't seem like MAXNC
- PRO (drives my Sherline) understands G17/18/19. Thinks they are all
in XY. Does anyone know if the DLX version (4-axis cnc) does (I think I
can upgrade)?

CNC Pro does (http://www.yeagerautomation.com/specs.htm), so that might
be a solution. I am still using 4-phase drive, don't know if CNC Pro
supports it. For what I am doing now, simple XY arcs are fine on the
Sherline. But later...

Alan

ballendo@... wrote:
> .................cut
> G0 X0Y0Z0 (keep it understandable, we'll start from zero)
> G90 G20 (absolute coordinate system, inches)
> G18 (select plane XZ for arcs)
> G02 X10 Z10 I5 K5 F25 (CW arc from 0,0,0 to 10,0,10 f/rate 25IPM)
> M01 (stop if operator has the optional stop switch on)
>
> This might be used to round the side of a left front fender on a
> model car.
> ............cut
> All snips above assume part surface is Z0.
>
> Hope this helps
>
> Ballendo

Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager




[Non-text portions of this message have been removed]