Re: [CAD_CAM_EDM_DRO] Re: These dad burn ads!!

I'd expect nothing less from a MARKETING guy.

Art

----- Original Message -----
From: "Wilfred Yellow" <wilfredyellow@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Thursday, September 02, 2004 9:16 PM
Subject: [CAD_CAM_EDM_DRO] Re: These dad burn ads!!


>
> You guys are certainly an inexhaustable supply of knowledge. I've just
been reading in more or less the side lines(since I joined) with only an
occasional comment to make and the odd request for assistance. I've been
gone for a few days and when I return my mail box has been inundated with
mail. Going over most of them it seems that most of you have a problem with
those advertisements that have been so boldly stuck on the top of the
correspondence. Truly, I fail to see what irks you'se so much. We are here
to read and learn from this are we not? It just seems like a very small
inconvenience to have to put up with when we get so much in return. Lighten
up ya'll the bottom line is always the "unholy" dollar. I feel it is no more
annoying than having to go over all these emails that have piled up over the
past few days. Even though it was my own doing for not sitting my email up
to handle this event. What I'm trying to say is, "its the medium and its
there to be exploited."
> That's my opinion and I'm sticking to it! The content of the message is
what matters is it not?
>
> Sincerely
> Wilfred Yellow
> Double Eagle Marketing
> ===========================
> Discover the Secrets to Wealth
> Download your FREE copy of
> "Soar With the Eagles,Share the Wealth" Booklet
> visit: http://www.double-eagle-marketing.com/partners/WY1251
> reply to: mailto:info@...
> ====================================================
> Please visit:
> http://www.freedownline.net/members/snookums681.html
> You will not be disappointed!!
> ==============================================
> http://www.themail.com/ref.htm?ref=1216320
> ==============================================
> ----- Original Message -----
> From: Alan Marconett KM6VV
> To: CAD_CAM_EDM_DRO@egroups.com
> Sent: Sunday, September 03, 2000 5:12 AM
> Subject: [CAD_CAM_EDM_DRO] Re:Gcode
>
>
>
>
> My Groups | CAD_CAM_EDM_DRO Main Page | Start a new group!
>
>
> Ballendo,
>
> Thanks for the examples. I can see some uses now. I inscribed three
> circles in three faces of cube, and generated code for it in VectorCAD.
>
> (three circles 9/2/00 alm)
> N05 F5
> N10 G00 X0.000 Y2.000 Z3.500
> N11 G19
> N12 G03 Y2.000 Z3.500 J0.000 K-1.500
> N13 G00 X3.500 Y2.000 Z4.000
> N14 G17
> N15 G03 X3.500 Y2.000 I-1.500 J0.000
> N16 G00 X3.500 Y0.000 Z2.000
> N17 G18
> N18 G02 X3.500 Z2.000 I-1.500 K0.000
> N19 G17
>
> I added the G17/18/19. I get how it works now. Doesn't seem like MAXNC
> - PRO (drives my Sherline) understands G17/18/19. Thinks they are all
> in XY. Does anyone know if the DLX version (4-axis cnc) does (I think I
> can upgrade)?
>
> CNC Pro does (http://www.yeagerautomation.com/specs.htm), so that might
> be a solution. I am still using 4-phase drive, don't know if CNC Pro
> supports it. For what I am doing now, simple XY arcs are fine on the
> Sherline. But later...
>
> Alan
>
> ballendo@... wrote:
> > .................cut
> > G0 X0Y0Z0 (keep it understandable, we'll start from zero)
> > G90 G20 (absolute coordinate system, inches)
> > G18 (select plane XZ for arcs)
> > G02 X10 Z10 I5 K5 F25 (CW arc from 0,0,0 to 10,0,10 f/rate 25IPM)
> > M01 (stop if operator has the optional stop switch on)
> >
> > This might be used to round the side of a left front fender on a
> > model car.
> > ............cut
> > All snips above assume part surface is Z0.
> >
> > Hope this helps
> >
> > Ballendo
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>
>
>
> [Non-text portions of this message have been removed]
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>