CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] cutting simulation software

Posted by Chris Hellyar
on 2000-09-29 13:57:10 UTC
I've been playing with desknc, which is a full stepper driver (step+dir)
etc, but does OK toolpath display testing in a graphical window. I probably
wont buy it for actually driving my machine, as the stepper outputs are not
that constant, due to graphical overhead I think. (It's dos based). On my
retro-fitted lathe I can hear the steppers change pitch when they are meant
to be moving at a constant speed.

Anyway, the graphical bit is quite handy.

Also Kellycam (windows based) is quite good, and it has much prettier
graphics, and dosn't need registration it's totally free, but again I'd not
use it to drive a "real" machine due to "lumpy" stepper output.

Both of those are 2D, dunno if you're looking for 3D or not...

Cheers, Chris.

* Design engineer, Assembly worker, Cleaner.
* Ohmark Electronics. PO Box 5302, Christchurch, New Zealand.
* http://www.ohmark.co.nz

----- Original Message -----
From: Joe Vicars <jvicars@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Saturday, September 30, 2000 7:06 AM
Subject: [CAD_CAM_EDM_DRO] cutting simulation software


> Is there a shareware cutting simulator? You put in G code and it
> shows you the tool path?
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Joe Vicars 2000-09-29 11:50:30 UTC cutting simulation software machines@n... 2000-09-29 13:19:17 UTC Re: cutting simulation software machines@n... 2000-09-29 13:25:58 UTC Re: cutting simulation software Chris Hellyar 2000-09-29 13:57:10 UTC Re: [CAD_CAM_EDM_DRO] cutting simulation software Jon Elson 2000-09-29 14:48:13 UTC Re: [CAD_CAM_EDM_DRO] cutting simulation software Tim Goldstein 2000-09-30 07:13:27 UTC RE: [CAD_CAM_EDM_DRO] cutting simulation software MRC 2000-09-30 12:36:54 UTC Re: [CAD_CAM_EDM_DRO] cutting simulation software fepap@t... 2000-09-30 16:33:13 UTC Re: cutting simulation software Jon Elson 2000-09-30 21:02:19 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software marble here 2000-09-30 23:07:02 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software Kenn Danner 2000-09-30 23:11:04 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software marble here 2000-09-30 23:27:58 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software marble here 2000-10-01 07:35:52 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software Alan Marconett KM6VV 2000-10-01 13:30:50 UTC Re: [CAD_CAM_EDM_DRO] cutting simulation software stratton@m... 2000-10-01 16:55:00 UTC Re: [CAD_CAM_EDM_DRO] cutting simulation software Jon Elson 2000-10-01 22:03:14 UTC Re: [CAD_CAM_EDM_DRO] Re: cutting simulation software