Re: [CAD_CAM_EDM_DRO] RE Master Control forWindows Real-time

The current version ( non-real time) can be found at

http://users.andara.com/~fenerty/master.htm

The real time version will be available in another couple months. It will
be a VAST improvement over the previous version.

Art .

----- Original Message -----
From: "marble here" <marble_h@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Friday, November 24, 2000 4:24 PM
Subject: Re: [CAD_CAM_EDM_DRO] RE Master Control forWindows Real-time


> Art I recall a while back you had Master control.
> What is the cost of it and where can one get it .I
> would like to check it out .
>
> John
>
> --- Art Fenerty <fenerty@...> wrote:
> > Alan:
> >
> > After Master Control is released, I will
> > probably release the interface
> > so visual basic programmers, etc.. can develop more
> > apps that are windows
> > real-time.
> >
> > Art
> > ----- Original Message -----
> > From: "Alan Marconett KM6VV" <KM6VV@...>
> > To: <CAD_CAM_EDM_DRO@egroups.com>
> > Sent: Friday, November 24, 2000 1:22 PM
> > Subject: Re: [CAD_CAM_EDM_DRO] Windows Real-time
> >
> >
> > > Art,
> > >
> > > Sounds interesting! a systray device? Do you
> > plan to publish it's
> > > interface and/or it's workings? It could open the
> > door for windows
> > > controller programs. I tend to keep down in the
> > driver/BIOS level code,
> > > and it's been probably 6 years since I wrote any
> > thing for windows.
> > > Guess I'd have to investigate these "systray
> > devices".
> > >
> > > Nice Work!
> > >
> > > Alan
> > >
> > > Art Fenerty wrote:
> > > >
> > > > Sorry, I should have mentioned, The real time
> > engine is a systray
> > device. To
> > > > exit it you must right click on the word
> > > > CNC in your system tray (beside the time). The
> > Engine is meant to be
> > used
> > > > from any program that needs cnc output. It is an
> > automation object
> > callable
> > > > by other programs.
> > > >
> > > > Art
> > > >
> > > > ----- Original Message -----
> > > > From: "Art Fenerty" <fenerty@...>
> > > > To: <CAD_CAM_EDM_DRO@egroups.com>
> > > > Sent: Thursday, November 23, 2000 2:36 PM
> > > > Subject: Re: [CAD_CAM_EDM_DRO] Windows Real-time
> > > >
> > > > > Hi All:
> > > > >
> > > > > I have completed (almost) the real-time
> > pulseing engine for
> > > > MasterControl
> > > > > and would be interested in any comments. I
> > have uploaded it into the
> > files
> > > > > area. Its only 150k zipped.
> > > > > The engine will pulse steppers at any
> > frequency from
> > > > > 1hz to 8192hz in increments of one hz. It is
> > all in ring 0
> > > > > code and is very fast and smooth. My CNC
> > router actually doubled in
> > speed
> > > > > from the increased stability
> > > > > at high frequency. It is only a beta run of
> > the engine in the file,
> > but
> > > > > allows you to pulse up to 4-axis at a time at
> > the
> > > > > above frequencies. You will notice that
> > nothing on the desktop will
> > > > > interfere with the pulseing (mouse etc..)
> > > > > but netword and/or heavy disk usage will cause
> > some instability. The
> > idea
> > > > is
> > > > > to have this engine taking care of pulsing
> > while the program has time
> > to
> > > > do
> > > > > more complex
> > > > > graphics and simulations. Please drop me a
> > note as to
> > > > > what you think. It has only been run on my
> > system so far,
> > > > > so my appologies in advance if it doesn't work
> > at all.
> > > > >
> > > > > Thanks,
> > > > > Art
> > >
> > > Welcome to CAD_CAM_EDM_DRO@...,an
> > unmoderated list for the
> > discussion of shop built systems, for CAD, CAM, EDM,
> > and DRO.
> > >
> > > Addresses:
> > > Post message: CAD_CAM_EDM_DRO@egroups.com
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > > Unsubscribe:
> > CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@egroups.com,
> > wanliker@...
> > > Moderator: jmelson@... [Moderator]
> > > URL to this page:
> > http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > bill,
> > > List Manager
> > >
> >
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an
> > unmoderated list for the discussion of shop built
> > systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe:
> > CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com,
> > wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page:
> > http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
> >
>
>
> __________________________________________________
> Do You Yahoo!?
> Yahoo! Shopping - Thousands of Stores. Millions of Products.
> http://shopping.yahoo.com/
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>