CAD CAM EDM DRO - Yahoo Group Archive

Re:

Posted by Gary Passon
on 1999-08-08 10:12:09 UTC
Wow.. More helpful info, but now I've got a couple of more questions. If this gets overwelming
let me know. First, is there a schematic for assembling a 20 amp supply from DanM's transformers.
I went to his site and these parts see to be part of the servo description. Do I need any other parts
from DanM site (or better yet is there anything else I can use.. short of time, longer on credit cards
(bg)). Is there a super overschematic? Electrical stuff kinda baffles me, but I'm a good robot!

TIA... to the "chips"

Gary Passon
---------------------------------------------------------------------------

Tim Goldstein wrote:

> From: "Tim Goldstein" <timg@...>
>
> Just some suggestions to widen your search.
> That is a Pentium 90 or faster, a PII is not required (but if you find a
> good deal, what the heck)
> 1 gig HD seems like it is more than plenty. I have Linux & EMC on a 850 MB
> machine and it worked fine.
>
> As far as power supplies, you need one for the stepper controller 18 - 36
> VDC and while 10 amp would probably get you by with the monster motors you
> have 15 or more would probably be better. You could get 2 of the
> transformers from Dan and hook them in parallel for a 20 amp supply.
>
> The DRO board is powered from the PC and it feedst eh encoders. No need for
> external power.
>
> Glad the web site has been a help. It is mostly stuff I have hijacked from
> this list and other sites <bg>
>
> Tim
> [Denver, CO]
>
> > -----Original Message-----
> > From: Gary Passon [mailto:gary@...]
> > Sent: Saturday, August 07, 1999 11:13 PM
> > To: CAD_CAM_EDM_DRO@onelist.com
> > Subject: Re: [CAD_CAM_EDM_DRO]
> >
> >
> > From: Gary Passon <gary@...>
> >
> > Thanks for the advice... I'm off tomorrow to try to find a PII
> > 90Mhz or faster with 32mb (maybe64mb)
> > of memory, a floppy, 2Gb or bigger HD and the list of video cards
> > from the site you provided.
> > Also looking for a basic 17in monitor. Hopefully, this will do
> > it. One more question, please.
> > After I build DanM controllers aren't I going to need a power
> > supply for the card and another
> > one for the stepper themselves? I suspect if I read DanM's
> > instructions this will be obvious, but
> > I haven't got to that part yet, so sorry if this is an obvious
> > question.BTW I've been to your site a
> > couple of times and gotten a lot by cruising around. Great job,
> > and very inspiring.
> >
> > Gary Passon (a hopeful soon to be linux'er)
> > ------------------------------------------------------------------
> > -------------------
> >
>
> --------------------------- ONElist Sponsor ----------------------------
>
> You can WIN $100 to Amazon.com by starting a new list at ONElist.
> Drawing is held each week through August 20. For details, go to
> http://www.onelist.com/info/onereachsplash3.html
>
> ------------------------------------------------------------------------
> Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> bill,
> List Manager

Discussion Thread

Gary Passon 1999-08-08 10:12:09 UTC Re: