Re: [CAD_CAM_EDM_DRO] 5/8 Ball leadscrew thrust bearing assemblies and nut flanges

Bill,

I would be interested in this, but I can't afford one immediately.


Tom Eldredge

----- Original Message -----
From: Rich D. <cmsteam@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, March 22, 2001 4:04 PM
Subject: Re: [CAD_CAM_EDM_DRO] 5/8 Ball leadscrew thrust bearing assemblies
and nut flanges


> Bill,
> I might go for that, to use on my yet to be aquired Clausing/Johansen/
> Rockwell....Mill.
> Sounds interesting.
> Rich D.
>
> Bill Griffin wrote:
> >
> > Would there be any interest from the group in purchasing ready made
> > leadscrew thrust bearing blocks, end supports and ball nut flanges.
> >
> > I have been speaking with a manufacturer who may be willing to make
> > up a quantity of assemblies.
> >
> > We had also discussed providing say 6 ft lengths of 5/8 ballscrew
> > with both ends machned for the thrust bearing, lock nut and pulley.
> > the user could then easily cut the 6 footer to lentch and then have 2
> > leadscrews.
> >
> > While it may be difficult to make one assemblie fit all, I believe
> > that if low cost assemblies were available, users could design their
> > machines around what is available.
> >
> > I have made a simple model of the thrust block design if anyone wants
> > to view it its at http://www.grifftek.com/thrust/block.htm
> >
> > Thanks
> >
> > Bill Griffin
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> > FAQ: http://www.ktmarketing.com/faq.html
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>