Re: [CAD_CAM_EDM_DRO] Re: G-Code Arc drawing question
Posted by
Dan Statman
on 2001-11-15 17:28:19 UTC
Fred,
Thank you, exactly the function I was looking for.
Dan.
Thank you, exactly the function I was looking for.
Dan.
----- Original Message -----
From: "Fred Smith" <imserv@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, November 15, 2001 6:22 PM
Subject: [CAD_CAM_EDM_DRO] Re: G-Code Arc drawing question
> --- In CAD_CAM_EDM_DRO@y..., "Dan Statman" <dan.statman@r...> wrote:
> > I have a somewhat unique situation, atleast I think it is unique.
>
> ...snip
>
> >Is there a way to tell the Cad program to break the arcs up
> > into tiny line segments so that I get the G01 output (many lines)
> instead of
> > G03 (or whatever the arc code is)?
>
>
> This is called interpolation. In Bobcad the command is on the 3D
> menu. In VectorCAD(yes even the "sorta" free one) it is Change-Break-
> Interpolate.
>
> Bobcad cannot cut arcs that are not located in the X-Y plane. They
> are automatically interpolated into line segments. Vector will cut
> either way.
>
> Vector will also let you independently scale the drawing so that
> it "grows" in the Y direction so that you can use the Y scale at 1:1
> on your machine, based directly on the Vector output. This way you
> can see what is happening. You can also scale the output without
> modifying the drawing by setting a scale for the output Type in PI
> for the value of pi to about 16 decimals. You can also use the
> Vector Connect at Z function to accurately control pickups between
> disconnected geometry.
>
> Best Regards, Fred Smith- IMService
> Listserve Special discounts and offers are at:
> http://209.69.202.197/cced.html
>
> imserv@... Voice:248-486-3600 or 800-386-1670 Fax: 248-486-
> 3698
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
Dan Statman
2001-11-15 09:01:08 UTC
G-Code Arc drawing question
dlantz@a...
2001-11-15 09:04:59 UTC
RE: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Dan Statman
2001-11-15 09:10:12 UTC
Re: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
dlantz@a...
2001-11-15 09:13:14 UTC
RE: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Alan Marconett KM6VV
2001-11-15 11:50:31 UTC
Re: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Kevin P. Martin
2001-11-15 12:51:19 UTC
RE: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Michael Milligan
2001-11-15 12:59:02 UTC
RE: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Dan Statman
2001-11-15 14:08:46 UTC
Re: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
Fred Smith
2001-11-15 15:22:44 UTC
Re: G-Code Arc drawing question
Dave Engvall
2001-11-15 15:59:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: G-Code Arc drawing question
Dan Statman
2001-11-15 17:28:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: G-Code Arc drawing question
Marcus & Eva
2001-11-15 19:05:34 UTC
Re: [CAD_CAM_EDM_DRO] G-Code Arc drawing question
shymu@b...
2001-11-15 19:39:12 UTC
Re: G-Code Arc drawing question
ballendo@y...
2001-11-15 19:58:15 UTC
Re: G-Code Arc drawing question
Dave Engvall
2001-11-15 21:16:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: G-Code Arc drawing question