RE: [CAD_CAM_EDM_DRO] Encoders - Slightly O.T.

I am pretty sure BEI has an intrinsicly safe module for their encoders. (
Any encoders? )
Look at http://www.beiied.com/electronics.html .

-----Original Message-----
From: Ed Koffeman [mailto:edk@...]
Sent: Saturday, January 19, 2002 9:32 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Encoders - Slightly O.T.


I was succesful in making an encoder for gasoline pumps back in the early
80's.

It passed the certification for CSA (Canada) at that time.

I used hall sensors and a multipole magnetic disk set up in a current loop
with the current limited by the circuitry at the counter.

It was optoisolated as well - I think that made it easier to certify.

You are allowed a fair bit of current as long as there's no capacitance at
the sensor. I think a regular optical head could be made
to work with some careful design.

You might try to see if the encoders used today in gasoline pumps would be
suitable. At the time I was doing it, they were only
available as reed sensors at very low resolutions so I had to roll my own.

Ed Koffeman

----- Original Message -----
From: "Jon Elson" <elson@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, January 19, 2002 12:54 AM
Subject: Re: [CAD_CAM_EDM_DRO] Encoders - Slightly O.T.


> Brian Walsh wrote:
>
> > Hi list,
> >
> > I'm looking for a source of shaft encoders (A + B O/P's), certified
> > intrinsically safe for use in a Zone 2 Hazardous Area. Any suggestions?
>
> Hmmm, intrinsically safe is not so easy for externally powered devices.
> Not only must the encoders be IntSafe, but the power source must
> also be rated IntSafe for use with the specific encoder, as well as
> the wiring, conduits, etc. I suspect you need to do serious research
> with Rockwell/Allen-Bradley, BEI, Heidenhain, or one of the other
> industrial encoder manufacturers. I'm sure they have all faced this
> at one time or another.
>
> Jon
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/