Unknown servo motor specs
Posted by
David Micklethwaite
on 2002-06-06 14:48:07 UTC
I have a couple of servo motors that I need to know more about before I try
to use them on a medium size mill I am trying to convert to CNC:
1. Label says "AMETEK, 40 V DC and some meaningless part numbers". The case
is 4" dia and 5" long with a 5/8" shaft at one end. The motor has two
brushes. How do I fugure out the maximum current for this motor? I would
have to drill the "back end" of the motor shaft to mount an encoder - is
this a reasonable thing to attempt?
2. Label says "Electro Craft Permanent Magnet Servo Motor". The case is
3.25" dia and 5" long. The motor has a 1/2" shaft at one end and a 1/4"
shaft at the other which has a small electro mechanical clutch or brake on
it. The motor has two brushes. There is no indication of voltage or current
on this motor so how do I figure out what it can take?
Both motors have been scavenged from old equipment and so I have no idea of
their background. For once though, I can get more if I decide to use them!
Regards,
Dave.
David Micklethwaite
Technical Sales Support Consultant, Cray Australia Pty Ltd
Phone: +61 2 6295 4012 Fax: +61 2 6232 6218
Suite 1, Level 2, 1-7 Franklin St, Manuka ACT, AUSTRALIA
Postal: PO Box 3543, Manuka ACT 2603, AUSTRALIA
to use them on a medium size mill I am trying to convert to CNC:
1. Label says "AMETEK, 40 V DC and some meaningless part numbers". The case
is 4" dia and 5" long with a 5/8" shaft at one end. The motor has two
brushes. How do I fugure out the maximum current for this motor? I would
have to drill the "back end" of the motor shaft to mount an encoder - is
this a reasonable thing to attempt?
2. Label says "Electro Craft Permanent Magnet Servo Motor". The case is
3.25" dia and 5" long. The motor has a 1/2" shaft at one end and a 1/4"
shaft at the other which has a small electro mechanical clutch or brake on
it. The motor has two brushes. There is no indication of voltage or current
on this motor so how do I figure out what it can take?
Both motors have been scavenged from old equipment and so I have no idea of
their background. For once though, I can get more if I decide to use them!
Regards,
Dave.
David Micklethwaite
Technical Sales Support Consultant, Cray Australia Pty Ltd
Phone: +61 2 6295 4012 Fax: +61 2 6232 6218
Suite 1, Level 2, 1-7 Franklin St, Manuka ACT, AUSTRALIA
Postal: PO Box 3543, Manuka ACT 2603, AUSTRALIA
Discussion Thread
David Micklethwaite
2002-06-06 14:48:07 UTC
Unknown servo motor specs
buzzardec
2002-06-06 16:14:50 UTC
Re: Unknown servo motor specs
mariss92705
2002-06-06 17:19:25 UTC
Re: Unknown servo motor specs
Jon Elson
2002-06-06 22:05:03 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
buzzardec
2002-06-06 23:00:02 UTC
Re: Unknown servo motor specs
William Scalione
2002-06-06 23:07:59 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
David Micklethwaite
2002-06-07 01:59:55 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
Jon Elson
2002-06-07 12:19:11 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
Jon Elson
2002-06-07 12:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
gittt2000
2002-06-08 04:34:53 UTC
Re: Unknown servo motor specs
William Scalione
2002-06-09 16:19:48 UTC
Re: [CAD_CAM_EDM_DRO] Unknown servo motor specs
William Scalione
2002-06-09 16:22:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Unknown servo motor specs