Real Bridgeport Servos for sale
Posted by
R Rogers
on 2005-02-10 11:12:05 UTC
Hello everyone,
I was fortunate enough to locate a lot of the exact same servos that I am using on my Bridgeport. I bought a quantity of these and will only have about ten to sell. They are Allen-Bradley 1326DS Brush type DC Nema 42 servos. 40.6in-lb 13.7 amps continuous, 30 amp peak stall current, 2500 RPM, 40v/krpm which make them 100 volt motors. They are 4.2" diameter and 15" long excluding shaft which is 5/8" diameter and 2.3" long with 3/16" keyway. They are being shipped here and will not be available until the middle of next week. I have run these on X,Y and Z (knee driven with 2.5:1 reduction without gas springs) daily for the last two years in a commercial setting and they are excellent motors. These are extremely high quality servos with tons of power and very smooth performance. And they are O-ring sealed to keep out coolant and debris. I run them on Gecko 320's at 64 VDC and about 15 amp supply current. I replaced the encoders with US digital E5S-200's on the three that I am currently
using, however the encoder that is included is a 1000CPT Allen bradley 5 volt encoder and would work fine and may require an external 5 volt supply and may not with a Gecko320. These are also equiped with a 24 volt brake that would need to be removed and is an easy job, just remove front plate and slide it out and replace front/end plate. If you've been looking for a big servo to move a gantry or power a knee with a Gecko320, these are it.
They are $1500 servos and I will be selling them at a fraction of that price. These are like new still in the box. I will post the middle of next week with the actual sale price and post a pic and dims on my website this evening. Price depends on how much fun the freight company has with my credit card.
www.rogersmachine.net
Ron
[Non-text portions of this message have been removed]
I was fortunate enough to locate a lot of the exact same servos that I am using on my Bridgeport. I bought a quantity of these and will only have about ten to sell. They are Allen-Bradley 1326DS Brush type DC Nema 42 servos. 40.6in-lb 13.7 amps continuous, 30 amp peak stall current, 2500 RPM, 40v/krpm which make them 100 volt motors. They are 4.2" diameter and 15" long excluding shaft which is 5/8" diameter and 2.3" long with 3/16" keyway. They are being shipped here and will not be available until the middle of next week. I have run these on X,Y and Z (knee driven with 2.5:1 reduction without gas springs) daily for the last two years in a commercial setting and they are excellent motors. These are extremely high quality servos with tons of power and very smooth performance. And they are O-ring sealed to keep out coolant and debris. I run them on Gecko 320's at 64 VDC and about 15 amp supply current. I replaced the encoders with US digital E5S-200's on the three that I am currently
using, however the encoder that is included is a 1000CPT Allen bradley 5 volt encoder and would work fine and may require an external 5 volt supply and may not with a Gecko320. These are also equiped with a 24 volt brake that would need to be removed and is an easy job, just remove front plate and slide it out and replace front/end plate. If you've been looking for a big servo to move a gantry or power a knee with a Gecko320, these are it.
They are $1500 servos and I will be selling them at a fraction of that price. These are like new still in the box. I will post the middle of next week with the actual sale price and post a pic and dims on my website this evening. Price depends on how much fun the freight company has with my credit card.
www.rogersmachine.net
Ron
[Non-text portions of this message have been removed]
Discussion Thread
Dan Mauch
2005-02-10 10:19:31 UTC
3D Scanner
R Rogers
2005-02-10 11:12:05 UTC
Real Bridgeport Servos for sale