Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
Posted by
Roy J. Tellason
on 2005-03-19 07:44:02 UTC
On Saturday 19 March 2005 08:39 am, Lance Hopper wrote:
rectifier outputs are fed to a common filter I don't see where the problem
is. Not that I'm saying there isn't one, just that I don't see it. If
there is can you point it out for me?
> Hello,If you wire up a 3ph transformer and each secondary is rectified and all
> I've been talking to the guy myself trying to help him out. He's
> already bought 200V 40A Rutex drives as I understand. Now he's
> trying to figure out the PS.
>
> The original drives were fed 120 3ph from the secondaries of a
> 2.5kva 3ph transformer as he describes via his electrical schematics.
> He was trying to see if the stock 3ph transformer (has delta and Y
> wiring configurations, he has the schematics, maybe he should post)
> could take ~220 1ph (all he has available) and output ~120 1ph that
> could be rectified and used for the Rutex drives. I doubted that it
> would work and be dangerous/stupid to try, but what do I know.
rectifier outputs are fed to a common filter I don't see where the problem
is. Not that I'm saying there isn't one, just that I don't see it. If
there is can you point it out for me?
Discussion Thread
snaketracks
2005-03-17 08:22:21 UTC
Motor calculations? Help!
Jon Elson
2005-03-17 09:46:23 UTC
Re: [CAD_CAM_EDM_DRO] Motor calculations? Help!
snaketracks
2005-03-18 13:10:42 UTC
Re: Motor calculations? Help!
Jon Elson
2005-03-18 18:10:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
cnc_4_me
2005-03-18 20:06:43 UTC
Re: Motor calculations? Help!
Jon Elson
2005-03-18 21:09:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
cnc_4_me
2005-03-18 21:53:48 UTC
Re: Motor calculations? Help!
Lance Hopper
2005-03-19 05:39:35 UTC
Re: Motor calculations? Help!
Jon Elson
2005-03-19 06:06:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
Jon Elson
2005-03-19 06:07:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
spc_aux
2005-03-19 06:13:32 UTC
Re: Motor calculations? Help!
spc_aux
2005-03-19 06:16:12 UTC
Re: Motor calculations? Help!
R Rogers
2005-03-19 06:19:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
Dan Mauch
2005-03-19 07:20:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
Roy J. Tellason
2005-03-19 07:44:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor calculations? Help!
spc_aux
2005-03-19 09:12:58 UTC
Re: Motor calculations? Help!
snaketracks
2005-03-19 09:49:55 UTC
Re: Motor calculations? Help!
snaketracks
2005-03-19 09:55:51 UTC
Re: Motor calculations? Help!
snaketracks
2005-03-19 10:01:05 UTC
Re: Motor calculations? Help!
cnc_4_me
2005-03-19 10:25:48 UTC
Re: Motor calculations? Help!