Re: [CAD_CAM_EDM_DRO] Lathe controller

The ahha software has an option that uses an encoder on the spindle and does
threading on the lathe.
Darrell

----- Original Message -----
From: Paul Devey <paul_devey@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: Sunday, July 02, 2000 11:22 PM
Subject: Re: [CAD_CAM_EDM_DRO] Lathe controller


> Jon,
>
> You are right. Microkinetics does threading. They have an encoder on the
> spindle to give positional feedback for threading. I have not seen this
done
> by anyother low cost controllers/SW packages.
>
> Paul Devey
> -----------------------------------------------------
> Click here for Free Video!!
> http://www.gohip.com/free_video/
>
> ----- Original Message -----
> From: Jon Anderson <janders@...>
> To: <CAD_CAM_EDM_DRO@egroups.com>
> Sent: Sunday, July 02, 2000 6:30 PM
> Subject: Re: [CAD_CAM_EDM_DRO] Lathe controller
>
>
> > john@... wrote:
> > >
> > > Can anyone recomend a controller for a lathe other than Ahha.
> >
> > Microkinetics is the only one I know of, and I can say only that I
> > -think- it'll thread. Next step up appears to be a pretty high one.
> >
> > Jon
> >
> > ------------------------------------------------------------------------
> > Free, Unlimited Calls Anywhere!
> > Visit Firetalk.com - click below.
> > http://click.egroups.com/1/5479/4/_/423600/_/962588055/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
> >
> >
>
>
> ------------------------------------------------------------------------
> Free Conference Calling with Firetalk!
> Host your next egroup meeting live on Firetalk.
> Click here!
> http://click.egroups.com/1/5478/4/_/423600/_/962594282/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>