Re: [CAD_CAM_EDM_DRO] How to deal with Stepper Motor heat - 150 degrees F

Hi, yep good ole heat...i would look carefully at how and what they are
mounted to, you might be able to add a sheet of alum with finns off out of
the way. one of my machines i removed the steel part the motor was mounted
on and made a new one of alum. i simply epoxied a heat sink to the top of
the motor and that has helped alot. might be able to take a thin backed
heatsink, bend it to the shape of the od of the motor and epoxy it on, or
stainless pipe camps. even a small amount of heat sink will make a
difference. cul brian f.

----- Original Message -----
From: "lcdpublishing" <lcdpublishing@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, August 23, 2006 11:23 AM
Subject: [CAD_CAM_EDM_DRO] How to deal with Stepper Motor heat - 150 degrees
F


> Hi guys,
>
> I ran a test the other day to see how hot the stepper motors are
> getting on my machine. After 30 minutes, they (3 of them) were all
> at 150 degrees F.
>
> The motors are 5 volt motors rated at 1.4 Amps, nema 17. I am
> driving them at 30 volts and 1.4 amps. The driver chip is the
> SLA7062M chip. This heat test was performed with the motors holding
> their position as that is the best way I know to "push them" for
> heat build up.
>
> I know I could get another transformer and drop the voltage, but
> would prefer to keep it at 30 volts for performance. I have a bit
> of room where I could add some chunks of aluminum for heat sinking,
> but not sure if that would get the temp down enough. I have no room
> for fans so I am sort of pondering what directions I can go to deal
> with this.
>
> As always, I am open to any and all suggestions or ideas.
>
> One interesting thing I heard from a very reliable source is that if
> I switch from the SLA7062M based driver to a Gecko driver, the motor
> heat would drop down significantly. However, I don't have the
> budget for 3 Geckos on this little machine.
>
> Chris
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.405 / Virus Database: 268.11.5/425 - Release Date: 8/22/06
>
>