CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder

Posted by marble here
on 2000-09-05 12:50:02 UTC
Dan you say you geared down the motor to 3300 rpm's
so a 3500 @90volt motor will just work out fine. The
local princess Auto Outlet has 15 of them in stock at
19:95 I will get two of them

And thank you for the reply

John

--- Dan Mauch <dmauch@...> wrote:
> The overall size of the toolpost grinder's footprint
> is 9X9. It swings a 7"
> diameter wheel. The motor is a 1/2HP 10,000 RPM
> motor geared down 3/1. I am
> using it on my 13X25 lathe. I use the Z axis under
> cnc stepper motor control
> using one of my 5A drivers for a power feed.
> Dan
>
> -----Original Message-----
> From: marble_h@... <marble_h@...>
> To: CAD_CAM_EDM_DRO@egroups.com
> <CAD_CAM_EDM_DRO@egroups.com>
> Date: Monday, September 04, 2000 6:30 PM
> Subject: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder
>
>
> >
> >Dan How would you like to give us some dimensions
> on that grinder you
> >made
> >
> >
> >Welcome to CAD_CAM_EDM_DRO@...,an
> unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM,
> and DRO.
> >
> >Addresses:
> >Post message: CAD_CAM_EDM_DRO@egroups.com
> >Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> >Unsubscribe:
> CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> >List owner: CAD_CAM_EDM_DRO-owner@egroups.com,
> wanliker@...
> >Moderator: jmelson@... [Moderator]
> >URL to this page:
> http://www.egroups.com/group/CAD_CAM_EDM_DRO
> >FAQ: http://www.ktmarketing.com/faq.html
> >bill,
> >List Manager
> >
> >
>
>


__________________________________________________
Do You Yahoo!?
Yahoo! Mail - Free email you can access from anywhere!
http://mail.yahoo.com/

Discussion Thread

Dan Mauch 2000-09-05 07:03:46 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder marble here 2000-09-05 12:50:02 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder Dan Mauch 2000-09-05 14:03:38 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder marble here 2000-09-05 14:08:47 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder Tim Goldstein 2000-09-05 15:51:33 UTC RE: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder P.J. & Aimee Ritz 2000-09-05 19:58:41 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder Dan Mauch 2000-09-05 20:04:04 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder Jon Elson 2000-09-05 21:49:27 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder dave engvall 2000-09-05 22:39:18 UTC Re: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder Tim Goldstein 2000-09-06 17:47:47 UTC RE: [CAD_CAM_EDM_DRO] Dan's Toolpost grinder