Re: [CAD_CAM_EDM_DRO] Re: Learning
Posted by
Alan Marconett KM6VV
on 2000-09-22 20:05:48 UTC
Ozzie,
Yeah, Vector is different, but once you get the hang of it, i.e. supplying say, a pair of points if you want to "connect" them with
a line, it starts making sense. Do the selections in the order they are needed; think of "machining order". But that's just my
take after a few months of use.
Enjoy!
Alan
Ozzie@... wrote:
Draw, draw, draw!
Yeah, Vector is different, but once you get the hang of it, i.e. supplying say, a pair of points if you want to "connect" them with
a line, it starts making sense. Do the selections in the order they are needed; think of "machining order". But that's just my
take after a few months of use.
Enjoy!
Alan
Ozzie@... wrote:
Draw, draw, draw!
> CAD is one of the few areas discussed here that I have a little
> experience with. I started drawing homes back when I built them, back
> when the programs I could afford had no parts except those you
> conjured yourself. I drew and drew and drew, sometimes 16 hours a day
> on a weekend.
> The only other tip I have is try to learn the proceedure used by your
> particular program,i.e. if you're drawing a hexagon, what does the
> program want first, second, etc.
>
> Learning Vector for me was a bear because the proceedure is so
> different from any other CAD program I've tried.
>
> Jerry
>
> --- In CAD_CAM_EDM_DRO@egroups.com, Dan Dowell <dandowell@s...> wrote:
> > Well I got into this turbo cad designer program that I bought. Even
> with the tutorial that comes with it this is hard to learn. It might
> take a couple of months.
> >
> > How did the members of this group learn to do cad programs? ANy
> common short cuts?
> >
> >
> > But at least I can say one thing, it does actually work.
> >
> >
> >
> > Dan
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
Dan Dowell
2000-09-21 14:28:44 UTC
Learning
Ozzie@h...
2000-09-21 14:48:04 UTC
Re: Learning
A. G. Eckstein
2000-09-21 15:08:13 UTC
Re: [CAD_CAM_EDM_DRO] Learning
Bob Campbell
2000-09-21 15:32:39 UTC
Re: [CAD_CAM_EDM_DRO] Learning
marble here
2000-09-21 16:08:31 UTC
Re: [CAD_CAM_EDM_DRO] Learning
Jon Anderson
2000-09-21 16:36:43 UTC
Re: [CAD_CAM_EDM_DRO] Learning
Alan Marconett KM6VV
2000-09-22 20:05:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Learning