Re: CNC PRO
Posted by
Dan Mauch
on 1999-07-01 06:02:09 UTC
See below;
Dan
-----Original Message-----
From: Jon Anderson <janders@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Wednesday, June 30, 1999 6:58 AM
Subject: Re: [CAD_CAM_EDM_DRO] CNC PRO
with all the variety of computers and compuuter speeds I don't think it
would be practical.
Dan
-----Original Message-----
From: Jon Anderson <janders@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Wednesday, June 30, 1999 6:58 AM
Subject: Re: [CAD_CAM_EDM_DRO] CNC PRO
>From: Jon Anderson <janders@...>I was impressed with his service.
>
>Dan,
>
>Nice to hear someone is supporting their program, especially at such a
>low cost. I looked over the site last night and emailed some questions.
>Probably going to give this a try.We'll it would be different but its easier to to do it with software and
>For an outside opinion, what do you think of his use of the timing chip
>on the motherboard to time stepper pulses as opposed to using timing
>loops in software? Could this be of any real world advantage, or is it
>just a different approach?
with all the variety of computers and compuuter speeds I don't think it
would be practical.
>
Discussion Thread
Dan Mauch
1999-06-30 06:38:13 UTC
Re: CNC PRO
Jon Anderson
1999-06-30 06:48:45 UTC
Re: CNC PRO
TADGUNINC@x...
1999-06-30 07:17:25 UTC
Re: CNC PRO
Bill Martin
1999-06-30 20:58:37 UTC
Re: CNC PRO
Jon Anderson
1999-06-30 21:24:19 UTC
Re: CNC PRO
Jon Elson
1999-06-30 23:34:17 UTC
Re: CNC PRO
Matt Shaver
1999-07-01 00:23:25 UTC
Re: CNC PRO
Dan Mauch
1999-07-01 06:03:42 UTC
Re: CNC PRO
Dan Mauch
1999-07-01 06:02:09 UTC
Re: CNC PRO
Jon Anderson
1999-07-01 06:43:27 UTC
Re: CNC PRO
Robert N Ash
1999-07-01 08:06:11 UTC
Re: CNC PRO
Jonty50@x...
1999-07-01 11:03:41 UTC
Re: CNC PRO
Jon Elson
1999-07-01 12:16:03 UTC
Re: CNC PRO
Tim Goldstein
1999-07-01 16:49:07 UTC
Re: CNC PRO
Jon Anderson
1999-07-01 17:30:53 UTC
Re: CNC PRO
Tim Goldstein
1999-07-01 17:38:09 UTC
Re: CNC PRO
Jon Anderson
1999-07-01 18:23:41 UTC
Re: CNC PRO
Matt Shaver
1999-07-01 21:36:50 UTC
Re: CNC PRO
Jon Elson
1999-07-02 22:17:51 UTC
Re: CNC PRO
jmesh@h...
2001-05-02 09:23:31 UTC
CNC PRO
Rich D.
2001-05-02 15:02:28 UTC
Re: [CAD_CAM_EDM_DRO] CNC PRO
cnc002@a...
2001-05-04 05:48:21 UTC
Re: [CAD_CAM_EDM_DRO] CNC PRO