Re: [CAD_CAM_EDM_DRO] Stepper Motors
Posted by
Smoke
on 2000-11-15 10:24:02 UTC
Ah! Now this is a good one!
Thanks, Smoke
-----Original Message-----
From: Carey L. Culpepper <mr.c@...>
To: CAD_CAM_EDM_DRO@egroups.com <CAD_CAM_EDM_DRO@egroups.com>
Date: Wednesday, November 15, 2000 10:53 AM
Subject: Re: [CAD_CAM_EDM_DRO] Stepper Motors
Thanks, Smoke
-----Original Message-----
From: Carey L. Culpepper <mr.c@...>
To: CAD_CAM_EDM_DRO@egroups.com <CAD_CAM_EDM_DRO@egroups.com>
Date: Wednesday, November 15, 2000 10:53 AM
Subject: Re: [CAD_CAM_EDM_DRO] Stepper Motors
>Gordon: Try this: http://compumotor.com/support.htmdiscussion of shop built systems, for CAD, CAM, EDM, and DRO.
>Click on search and type in motor sizing. They have a lot of information
>on their site. I hope this helps.
>Carey
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>
Discussion Thread
Dan Mauch
1999-07-16 09:01:34 UTC
Re: Stepper Motors
James Cullins
2000-04-01 06:18:18 UTC
Stepper Motors
Tim Goldstein
2000-04-01 09:42:35 UTC
RE: [CAD_CAM_EDM_DRO] Stepper Motors
Gordon Robertson
2000-11-15 09:30:20 UTC
Stepper Motors
Smoke
2000-11-15 09:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Carey L. Culpepper
2000-11-15 09:54:44 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Smoke
2000-11-15 10:24:02 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Joe Vicars
2000-11-15 10:35:04 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Mike Chaney
2001-12-07 14:18:57 UTC
Stepper Motors
cadcamcenter
2001-12-08 01:46:35 UTC
Re: Stepper Motors
Jon Elson
2001-12-08 21:16:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motors
jess@p...
2004-04-29 01:21:36 UTC
Stepper Motors
Dan Mauch
2004-04-29 05:42:52 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
jess@p...
2004-04-29 08:05:22 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Jon Elson
2004-04-29 09:17:02 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Tony Jeffree
2004-04-29 09:29:50 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
bull2002winkle
2004-04-29 09:49:15 UTC
Re: Stepper Motors
treadlemill
2004-04-30 06:50:54 UTC
Re: Stepper Motors
JanRwl@A...
2004-04-30 21:32:53 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
turbulatordude
2004-05-02 07:40:37 UTC
Re: Stepper Motors - output steps
treadlemill
2004-05-02 20:53:36 UTC
Re: Stepper Motors - output steps