Re: Stepper Motors
Posted by
treadlemill
on 2004-04-30 06:50:54 UTC
---I have been playing around with stepper motors in a hobby
capacity for several years and have come to the following
conclusions.
I believe that the difference between series and parallel wound and
wired steppers does not apply when using the parallel port.
I have wired 8 lead motors in both series and parallel and timed the
moves and found no difference. I use new, current rather expensive
microstep drives that req. some switch changes to optimise different
motor charateristics. Even doubling a 24v supply did not make the
difference that gets discussed about on lists.
I do not use my best computer in the basement but after finding that
there is little difference between timed G00 moves when using an old
486/33 and a less old P/133 I did not think using a better computer
would change things too much.
I use TCNC which suits me so perhaps there are programs that can
output a faster step rate?
I could be wrong but I do not think with my setup I get to the part
of the curve where speed and torque drop off occur so there is
little point worrying about things like series, parallel, voltage,
inductance and torque reduction. Studying manufacturers specs seem
to qualify this for me.
Indexers seem be to used in industrial applications of steppers so
perhaps they can output a step rate where there would be a
difference in performance with series or parallel configurations?
T
In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
capacity for several years and have come to the following
conclusions.
I believe that the difference between series and parallel wound and
wired steppers does not apply when using the parallel port.
I have wired 8 lead motors in both series and parallel and timed the
moves and found no difference. I use new, current rather expensive
microstep drives that req. some switch changes to optimise different
motor charateristics. Even doubling a 24v supply did not make the
difference that gets discussed about on lists.
I do not use my best computer in the basement but after finding that
there is little difference between timed G00 moves when using an old
486/33 and a less old P/133 I did not think using a better computer
would change things too much.
I use TCNC which suits me so perhaps there are programs that can
output a faster step rate?
I could be wrong but I do not think with my setup I get to the part
of the curve where speed and torque drop off occur so there is
little point worrying about things like series, parallel, voltage,
inductance and torque reduction. Studying manufacturers specs seem
to qualify this for me.
Indexers seem be to used in industrial applications of steppers so
perhaps they can output a step rate where there would be a
difference in performance with series or parallel configurations?
T
In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
>motors 2.5A
>
> jess@p... wrote:
>
> >What is the advantage or disadvantage between these two stepper
> >and 4.5A .speed
> >
> >H34013 Step motor 1076 oz in 2.5A 3. ohms
> >H34014 Step motor 1076 oz in 4.5A 1. ohms
> >
> >
> The 34014 motor will produce the same torque at a somewhat higher
> than the 34013 motor, because of the lower resistance andinductance.
>speeds
> However, both of these motors will be severely limited at higher
> due to the high resistance. For a 1076 Oz-In motor, you reallywant a
> super-lowGecko 201
> resistance motor, with perhaps a rating of 7A / phase if used with
> drives, or even higher if using drives capable of greater current.out of
>
> I'd take a wild guess and say that even the 34014 motor will run
> torque
> well below 1000 RPM.
>
> Jon
Discussion Thread
Dan Mauch
1999-07-16 09:01:34 UTC
Re: Stepper Motors
James Cullins
2000-04-01 06:18:18 UTC
Stepper Motors
Tim Goldstein
2000-04-01 09:42:35 UTC
RE: [CAD_CAM_EDM_DRO] Stepper Motors
Gordon Robertson
2000-11-15 09:30:20 UTC
Stepper Motors
Smoke
2000-11-15 09:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Carey L. Culpepper
2000-11-15 09:54:44 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Smoke
2000-11-15 10:24:02 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Joe Vicars
2000-11-15 10:35:04 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Mike Chaney
2001-12-07 14:18:57 UTC
Stepper Motors
cadcamcenter
2001-12-08 01:46:35 UTC
Re: Stepper Motors
Jon Elson
2001-12-08 21:16:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motors
jess@p...
2004-04-29 01:21:36 UTC
Stepper Motors
Dan Mauch
2004-04-29 05:42:52 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
jess@p...
2004-04-29 08:05:22 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Jon Elson
2004-04-29 09:17:02 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
Tony Jeffree
2004-04-29 09:29:50 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
bull2002winkle
2004-04-29 09:49:15 UTC
Re: Stepper Motors
treadlemill
2004-04-30 06:50:54 UTC
Re: Stepper Motors
JanRwl@A...
2004-04-30 21:32:53 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motors
turbulatordude
2004-05-02 07:40:37 UTC
Re: Stepper Motors - output steps
treadlemill
2004-05-02 20:53:36 UTC
Re: Stepper Motors - output steps