CAD CAM EDM DRO - Yahoo Group Archive

RE: Stepper Power Supply

Posted by John Ross
on 1999-08-13 14:12:05 UTC
I'm using oriental motors vexta ph299 series.

specs from the oriental motor 1997 catalog...
<snip>
holding torque - 375 oz-in unipolar
current per phase - 4 amps unipolar, 2.82 amps bipolar
voltage per phase - 3 volts unipolar, 4.25 volts bipolar
winding specs. - 0.75 ohm/winding and 4.5 mh/winding
<snip>

John R.
-----Original Message-----
From: Dan Mauch [mailto:dmauch@...]
Sent: Friday, August 13, 1999 2:33 PM
To: CAD_CAM_EDM_DRO@onelist.com
Subject: Re: [CAD_CAM_EDM_DRO] Stepper Power Supply


From: "Dan Mauch" <dmauch@...>

Depends on the stepper motor s that you use. What is the current rating of
each motor?
Dan
-----Original Message-----
From: WAnliker@... <WAnliker@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Friday, August 13, 1999 11:51 AM
Subject: Re: [CAD_CAM_EDM_DRO] Stepper Power Supply


>From: WAnliker@...
>
>In a message dated 8/13/99 11:36:29 AM Pacific Daylight Time,
>johnr@... writes:
>
><<
> Hey looking through my junk I've found a 110v -> 24v 5amp transformer and
a
> 25amp 50 VPIV rectifier. Anyone know if these will work with the
Camtronics
> 5amp kit?
>
> JR >>
>The transformer will work. The rectifier with only 50PIV is iffy, it
should
>be much higher, 3x voltage of the transformer is about minimum, higher is
>better.
>bill
>
>--------------------------- ONElist Sponsor ----------------------------
>
>ONElist now brings ICQ Instant Messaging to members
>For details,
><a href=" http://www.onelist.com/info/news.html ">Click Here</a>
>
>------------------------------------------------------------------------
>Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>bill,
>List Manager
>


--------------------------- ONElist Sponsor ----------------------------

ONElist: your connection to people who share your interests.

------------------------------------------------------------------------
Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the
discussion of shop built systems in the above catagories.
To Unsubscribe, read archives, change to or from digest.
Go to: http://www.onelist.com/isregistered.cgi
Log on, and you will go to Member Center, and you can make changes there.
bill,
List Manager

Discussion Thread

John Ross 1999-08-13 11:23:01 UTC Stepper Power Supply WAnliker@x... 1999-08-13 11:51:33 UTC Re: Stepper Power Supply Robert Bachman 1999-08-13 16:12:02 UTC Re: Stepper Power Supply Dan Mauch 1999-08-13 13:32:41 UTC Re: Stepper Power Supply John Ross 1999-08-13 14:12:05 UTC RE: Stepper Power Supply John Ross 1999-08-13 14:23:24 UTC RE: Stepper Power Supply Dan Mauch 1999-08-13 16:00:20 UTC Re: Stepper Power Supply Bertho Boman 1999-08-13 16:14:35 UTC Re: Stepper Power Supply Bertho Boman 1999-08-13 21:47:34 UTC Re: Stepper Power Supply