CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Solid State Relays

Posted by Andy Olney
on 2001-04-07 16:15:28 UTC
Current draw for these relays is about 4.4 mA at 4.9 Volts.

-----Original Message-----
From: Andy Olney [mailto:andy@...]
Sent: Thursday, April 05, 2001 6:18 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] Re: Solid State Relays


The relays were about $4 each and will control 10A at 230 V. Have not put my
ammeter in line with the parallel port but I will and report back. Andy

-----Original Message-----
From: tauseef [mailto:alieron@...]
Sent: Wednesday, April 04, 2001 10:29 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Solid State Relays


hi andy,
thanks for the info. Can you tell me what the voltage output on your
computer port is? How many milliamps do you get. Reason I ask is my
brother made a board for me to control the spindle but it needed to
be through a optoisolator and relay/transistor combo. My labtop only
puts out about 4.25 volts at about 6 millamps (or something that
small). How much where the relays?
thanks
tauseef


--- In CAD_CAM_EDM_DRO@y..., andy@o... wrote:
> I just got a few solid state relays from Marlin P. Jones
www.mpja.com
> #4062-RL. Input is 2.8 to 24 VDC and my parallel port was able to
> drive them directly with no intervening circuitry. Opto isolated
also.
> They would be good to turn on that coolant pump, mister, etc.
> Andy


Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager

FAQ: http://www.ktmarketing.com/faq.html

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

Tom 2000-12-29 09:39:41 UTC Solid State Relays Doug Harrison 2000-12-29 11:29:37 UTC Re: [CAD_CAM_EDM_DRO] Solid State Relays Tim Goldstein 2000-12-29 16:34:09 UTC RE: [CAD_CAM_EDM_DRO] Solid State Relays andy@o... 2001-04-04 13:36:37 UTC Solid State Relays tauseef 2001-04-04 22:29:17 UTC Re: Solid State Relays Andy Olney 2001-04-05 06:17:33 UTC RE: [CAD_CAM_EDM_DRO] Re: Solid State Relays Doug Harrison 2001-04-05 17:57:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Solid State Relays Andy Olney 2001-04-07 16:15:28 UTC RE: [CAD_CAM_EDM_DRO] Re: Solid State Relays