Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
Posted by
Smoke
on 2001-05-10 18:51:43 UTC
YES! Graphite is an excellent lube. In fact that's what is recommended (at
gunsmithing school) for lubing actions.
Graphite doesn't attract adust and crud the way liguid or paste lubes do.
Smoke
gunsmithing school) for lubing actions.
Graphite doesn't attract adust and crud the way liguid or paste lubes do.
Smoke
>Stan, graphite is a lubricant in itself I believe. I'd wipe downdiscussion of shop built systems, for CAD, CAM, EDM, and DRO.
>as much as possible, re-grease with your choice, then check accuracy
>and repeatability, as well as the smoothness of motion.
>
>Mike
>
>>
>>Next step is a real good cleaning. The one hand crank on the Y axis
>>(left-right?) doesn't feel very smooth and I am thinking of the
>>graphite in and on the ball screws. Yes, its all over, and up under
>>the table on the screws. What is the best way to clean these ball
>>screws. Now I am going to guess - DONT TAKE IT APART! If my guess is
>>true then does one just flush it out, wipeing down the exposed shaft
>>and moving the nut from one side to the other, repeating this till
>>its all cleaned out?
>>
>>
>>Thanks, Stan Krumme. KO6YB
>>
>>
>>
>>
>>
>>
>>
>>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>>discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>>
>>Addresses:
>>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>>Moderator: jmelson@... timg@... [Moderator]
>>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>bill,
>>List Manager
>>
>>FAQ: http://www.ktmarketing.com/faq.html
>>
>>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>--
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
skrumme@c...
2001-05-10 18:06:18 UTC
PLEASE HELP in cleanup of bridgeport
Mike
2001-05-10 18:39:01 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
Smoke
2001-05-10 18:51:43 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
Jon Anderson
2001-05-10 19:46:44 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
JanRwl@A...
2001-05-10 20:05:38 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
Sven Peter, TAD S.A.
2001-05-12 07:53:19 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
Jon Elson
2001-05-13 22:52:33 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport
stratton@m...
2001-05-14 10:06:07 UTC
Re: [CAD_CAM_EDM_DRO] PLEASE HELP in cleanup of bridgeport