CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Stepper Controller

Posted by Tim Goldstein
on 2001-05-20 12:06:07 UTC
Good question and a fun way to start.

All you need is a switch to control the direction and a quick little circuit
with a 555 timer to act as the step generator. Probably take less then $3.00
in parts for the "controller". You will still need the stepper driver (Gecko
G201/G210, Camtronics 5 amp or 2 amp, L297/298 based unit, etc) and a power
supply, just no computer. When you decide to go full CNC you can just remove
the circuit and hook the computer in it's place.

Tim
[Denver, CO]

> -----Original Message-----
> Hello I am a new member to this group, and pretty new to the whole
> stepper motor/cnc bizz, I was wondering if someone has plans to a
> motor controller that doesnt need a computer, but rather could be used
> as a power feed of some sort... you press a button it spins one
> way(maby have a rehastat to speed or slow it down), press another
> button makes it spin the other way, and maby a button to advance one
> step at a time?
>
> Any info would be great! good group!
>
> Tyler Phillips
>
>
> FAQ: http://www.ktmarketing.com/faq.html
>

Discussion Thread

powernob@h... 2001-05-20 11:50:26 UTC Stepper Controller powernob@h... 2001-05-20 11:51:46 UTC Stepper Controller Tim Goldstein 2001-05-20 12:06:07 UTC RE: [CAD_CAM_EDM_DRO] Stepper Controller Alan Marconett KM6VV 2001-05-20 14:37:50 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller powernob@h... 2001-05-20 16:20:06 UTC Re: Stepper Controller Carol & Jerry Jankura 2001-05-20 16:47:13 UTC RE: [CAD_CAM_EDM_DRO] Re: Stepper Controller Smoke 2001-05-20 16:52:49 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller DRigotti@A... 2001-05-20 16:59:37 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller Alan Marconett KM6VV 2001-05-20 17:34:53 UTC Re: Stepper Controller Ian Wright 2001-05-21 01:54:41 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller John Guenther 2001-05-21 05:34:56 UTC RE: [CAD_CAM_EDM_DRO] Stepper Controller Garry & Maxine Foster 2001-05-21 06:24:04 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller wanliker@a... 2001-05-21 09:03:15 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller Sven Peter, TAD S.A. 2001-05-21 11:43:46 UTC Re: [CAD_CAM_EDM_DRO] Stepper Controller Tim Goldstein 2001-05-21 12:27:55 UTC RE: [CAD_CAM_EDM_DRO] Stepper Controller Alan Marconett KM6VV 2001-05-21 15:35:34 UTC Re: Stepper Controller ballendo@y... 2001-05-21 21:31:09 UTC Re: Stepper Controller wanliker@a... 2001-05-22 00:15:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Stepper Controller