Re: Stepper Wire ?
Posted by
zephyrus@r...
on 2001-07-10 14:36:13 UTC
--- In CAD_CAM_EDM_DRO@y..., Jon Elson <elson@p...> wrote:
I'm still wondering about the outcome of this. I'm currently (no pun
intended) using some scavenged 20ga-7-strand-
2-twisted-foil-shielded-pair wire on my motors, but it's not very
flexible at all and as you say, Jon, I worry about the durability
of the foil shielding with flexing.
Braid-shielded multistrand flexible cable is $$$, but Newark has some
Belden unshielded "Infinity" 9-million-flex rated cable (74x38 strand)
at $1.66/foot for 20-ga 4-conductor.
Are you implying that because of the slowly varying current, that
shielding is not necessary, or is that wishful thinking on my part?
My drivers are 2A current limited, and I'm running <=4000 steps/sec.
Best regards,
Randy
> Not true. There may be voltages with square corners, but thecurrents
> are very slowly changing triangle waves, due to motor windinginductance.
I'm still wondering about the outcome of this. I'm currently (no pun
intended) using some scavenged 20ga-7-strand-
2-twisted-foil-shielded-pair wire on my motors, but it's not very
flexible at all and as you say, Jon, I worry about the durability
of the foil shielding with flexing.
Braid-shielded multistrand flexible cable is $$$, but Newark has some
Belden unshielded "Infinity" 9-million-flex rated cable (74x38 strand)
at $1.66/foot for 20-ga 4-conductor.
Are you implying that because of the slowly varying current, that
shielding is not necessary, or is that wishful thinking on my part?
My drivers are 2A current limited, and I'm running <=4000 steps/sec.
Best regards,
Randy
Discussion Thread
Al Schoepp
2001-06-16 17:17:27 UTC
driver wiring questions
Jon Elson
2001-06-16 17:30:09 UTC
Re: [CAD_CAM_EDM_DRO] driver wiring questions
Tim Goldstein
2001-06-16 19:19:44 UTC
RE: [CAD_CAM_EDM_DRO] driver wiring questions
Hugh & Denise Currin
2001-06-18 17:11:00 UTC
Stepper Wire ?
Matt Shaver
2001-06-19 00:29:51 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Wire ?
ptengin@a...
2001-06-19 04:02:42 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Wire ?
Jon Elson
2001-06-19 17:10:46 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Wire ?
zephyrus@r...
2001-07-10 14:36:13 UTC
Re: Stepper Wire ?
mariss92705@y...
2001-07-10 15:31:45 UTC
Re: Stepper Wire ?
Eric Keller
2001-07-10 17:14:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Wire ?
Jon Elson
2001-07-10 20:57:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Wire ?
van halcomb
2001-07-10 21:20:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Wire ?
Randy Gordon-Gilmore
2001-07-11 22:35:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Wire ?
mariss92705@y...
2001-07-12 07:51:08 UTC
Re: Stepper Wire ?