Re: [CAD_CAM_EDM_DRO] Langlois's HSM EDM m/c question
Posted by
diazden
on 2001-07-23 08:48:28 UTC
Dave;
you can also see the series of articles by model engineering workshop
magazine on their spark erosion
machine it is based on the design by mr Langlois, and I
believe that even the pcb is available
regards from OZ
mariano
you can also see the series of articles by model engineering workshop
magazine on their spark erosion
machine it is based on the design by mr Langlois, and I
believe that even the pcb is available
regards from OZ
mariano
----- Original Message -----
From: "Dave Mitchell" <davem@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, July 23, 2001 8:47 PM
Subject: Re: [CAD_CAM_EDM_DRO] Langlois's HSM EDM m/c question
> "Ian Wright" <Ian@...> wrote:
> > Is this article part of the original series or is it a later follow-up.
If
> > the latter I have missed it - what extra benefit does it give?
>
> It was in part 6 of the original series, which consisted of
> outlines of extra bits of circuitry you might want to use - it included
> a circuit diagram, but no component values. One bit was limiter ciruitry -
> so it would stop when a microswitch indicated the end stop had been
reached.
> The other was a big transistor either side of the discharge capacitors,
> so you could alternately charge and dischage them, with variable frequency
> and duty cycle. This also means that the spark rate wasn't tied to 50/60
Hz.
> The article hinted that this gave better quality finish if you wanted to
> do something more than just burn out old studs. It also implied that
> the discharge capacitors could be made a lot smaller.
>
> Like the orignal poster, I'd be very interested to hear if anyone has
> built this 'advanced' model, what final circuit details they used,
> and what results were achieved.
>
> Dave M.
>
> PS - a big hello from Sheffield :-)
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
Brian Fairey
2001-07-21 05:12:28 UTC
Langlois's HSM EDM m/c question
Ian Wright
2001-07-21 11:41:14 UTC
Re: [CAD_CAM_EDM_DRO] Langlois's HSM EDM m/c question
Dave Mitchell
2001-07-23 03:48:04 UTC
Re: [CAD_CAM_EDM_DRO] Langlois's HSM EDM m/c question
phrh@w...
2001-07-23 08:30:34 UTC
Re: Langlois's HSM EDM m/c question
diazden
2001-07-23 08:48:28 UTC
Re: [CAD_CAM_EDM_DRO] Langlois's HSM EDM m/c question