Re: [CAD_CAM_EDM_DRO] Small Problem
Posted by
Weyland
on 2001-08-03 16:17:12 UTC
From: "Alan Marconett KM6VV" <KM6VV@...>
The plasma cutter isn't gonna be that big really.
(I'm outta space~!)
I figure it should hold a 2'x4' piece of sheet metal,
*MAYBE* 4'x4' at the *most*.
And of course, it only has to be able to move the torch head.
I thought I would be able to get away with using 60's on the plasma table.
You think the 125's would be okay?
Weyland
>Ahhhh, I was hoping you wouldn't say that! (:>)
> The RF mills (I have an RF-31) are gonna take bigger motors! About 450
> oz/in, from what I remember people saying. Others can probably advise
> on the motors for the plasma cutter. How big is it?
The plasma cutter isn't gonna be that big really.
(I'm outta space~!)
I figure it should hold a 2'x4' piece of sheet metal,
*MAYBE* 4'x4' at the *most*.
And of course, it only has to be able to move the torch head.
> Rigotti's driver board has UCN5804B's (UNIPOLAR), and is suitable forReally? (:<)
> the 60 oz/in motors. So I'm not sure where you were going to use it.
> Your two applications call for some bigger motors!
I thought I would be able to get away with using 60's on the plasma table.
You think the 125's would be okay?
> An you really themAhh, kewl, thanks.
> to be BIPOLAR, with chopper drivers. Otherwise You'd need terrible big
> L/R resistors, and you'd have a LOT of heat to get rid of!
> > ... driving unipolar motors with bipolar drivers...So much to learn...
>
> Depends on which Unipolar motors you are talking about! A lot are 6 or
> 8 wire, and with these, you just use 1/2 of each winding phase. You DO
> NOT want anything "common" between the two windings. It will let the
> magic smoke out of the drivers!
> Good luck man!Thanks~! I'll get there...
Weyland
Discussion Thread
Weyland
2001-08-02 09:08:02 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Alan Marconett KM6VV
2001-08-02 13:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Weyland
2001-08-02 14:14:18 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
brian
2001-08-02 17:07:09 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Carol & Jerry Jankura
2001-08-02 18:19:36 UTC
RE: [CAD_CAM_EDM_DRO] Small Problem
Alan Marconett KM6VV
2001-08-02 18:58:20 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Weyland
2001-08-03 15:11:34 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Weyland
2001-08-03 15:15:23 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Alan Marconett KM6VV
2001-08-03 16:08:13 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Weyland
2001-08-03 16:17:12 UTC
Re: [CAD_CAM_EDM_DRO] Small Problem
Carol & Jerry Jankura
2001-08-03 17:36:18 UTC
RE: [CAD_CAM_EDM_DRO] Small Problem