RE: [CAD_CAM_EDM_DRO] Re: USB on Linux
Posted by
Carol & Jerry Jankura
on 2001-10-17 05:01:01 UTC
Les:
Is an item such as an intelligent USB->Stepper Driver kit something that you
might consider as a side business? Perhaps add a few extra lines as
programmable I/O.
-- Jerry Jankura
Strongsville, Ohio
So many toys, So little time....
| -----Original Message-----
| From: Les Newell [mailto:les@...]
| Sent: Wednesday, October 17, 2001 1:57 AM
| To: CAD_CAM_EDM_DRO@yahoogroups.com
| Subject: Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
|
|
| There are lots of microcontrollers out there that have everything
| on board,
| for less than the cost of an FPGA. However I suppose I could be considered
| biased as I spend most of my working life dealing with microcontrollers..
|
| Les
|
| >
| > That's another reason why I did my interface on the parallel port.
| > Although there is an incredibly complex protocol for intelligent devices
| > associated with IEEE-1284, you don't have to use it. I chose not
| > to incur all that overhead. I can use $6 CPLD logic chips
| (lower density
| > than a true FPGA) to handle the lower-level bus protocol and run
| > my DAC or digital I/O. For the encoder counter or stepper rate
| generator,
| > I needed to implement these more complex functions, so I put it all on
| > an $18 FPGA. With a processor, unless it is all integrated, you need
| > RAM, ROM, the peripheral function itself, the CPU, the bus interface,
| > etc.
| >
|
|
|
| Addresses:
| FAQ: http://www.ktmarketing.com/faq.html
| FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
| Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
| Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
| Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
| List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
| Moderator: jmelson@... timg@... [Moderator]
| URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
| bill,
| List Manager
|
|
|
| Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
Is an item such as an intelligent USB->Stepper Driver kit something that you
might consider as a side business? Perhaps add a few extra lines as
programmable I/O.
-- Jerry Jankura
Strongsville, Ohio
So many toys, So little time....
| -----Original Message-----
| From: Les Newell [mailto:les@...]
| Sent: Wednesday, October 17, 2001 1:57 AM
| To: CAD_CAM_EDM_DRO@yahoogroups.com
| Subject: Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
|
|
| There are lots of microcontrollers out there that have everything
| on board,
| for less than the cost of an FPGA. However I suppose I could be considered
| biased as I spend most of my working life dealing with microcontrollers..
|
| Les
|
| >
| > That's another reason why I did my interface on the parallel port.
| > Although there is an incredibly complex protocol for intelligent devices
| > associated with IEEE-1284, you don't have to use it. I chose not
| > to incur all that overhead. I can use $6 CPLD logic chips
| (lower density
| > than a true FPGA) to handle the lower-level bus protocol and run
| > my DAC or digital I/O. For the encoder counter or stepper rate
| generator,
| > I needed to implement these more complex functions, so I put it all on
| > an $18 FPGA. With a processor, unless it is all integrated, you need
| > RAM, ROM, the peripheral function itself, the CPU, the bus interface,
| > etc.
| >
|
|
|
| Addresses:
| FAQ: http://www.ktmarketing.com/faq.html
| FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
| Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
| Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
| Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
| List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
| Moderator: jmelson@... timg@... [Moderator]
| URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
| bill,
| List Manager
|
|
|
| Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
Discussion Thread
Gordon R. Hawkinson
2001-10-15 23:15:02 UTC
USB on Linux
Eric Keller
2001-10-16 05:55:24 UTC
Re: [CAD_CAM_EDM_DRO] USB on Linux
Carol & Jerry Jankura
2001-10-16 06:28:49 UTC
RE: [CAD_CAM_EDM_DRO] USB on Linux
Ray
2001-10-16 07:02:35 UTC
Re: USB on Linux
Matt Shaver
2001-10-16 08:22:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
stevesng@n...
2001-10-16 09:28:44 UTC
Re: USB on Linux
Jon Elson
2001-10-16 10:21:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Les Newell
2001-10-16 12:27:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Jon Elson
2001-10-16 20:04:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Ray
2001-10-16 20:17:19 UTC
Re: Re: Re: USB on Linux
Les Newell
2001-10-17 02:15:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Carol & Jerry Jankura
2001-10-17 05:01:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: USB on Linux
Jon Elson
2001-10-17 11:23:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Les Newell
2001-10-17 12:56:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB on Linux
Carol & Jerry Jankura
2001-10-17 13:24:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: USB on Linux