RE: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
Posted by
Dan Mauch
on 2001-11-06 07:13:14 UTC
That's strange because two years ago when I bought some 5/8D 5 TPI
rolled ballscrews and nuts from Mc Master they had Thompson labels on
the nuts and the ballscrews were in tubes marked Thompson.
Dan
-----Original Message-----
From: Chris L [mailto:datac@...]
Sent: Monday, November 05, 2001 8:13 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw
adjustment? and Rolled Ballscrews
Ballendo,
An EXCELLENT Post. Thank you.
A side note: A kerk salesman told me that they were the sole supplier
to Mcmaster for Rolled leadscrews and Anti-backlash nuts. Unfortunately,
Mcmaster does not carry Kerks "Good" Nuts just the cheapy ones. But,
I've seen them run on retail 20K routers day in and day out......
Chris L
rolled ballscrews and nuts from Mc Master they had Thompson labels on
the nuts and the ballscrews were in tubes marked Thompson.
Dan
-----Original Message-----
From: Chris L [mailto:datac@...]
Sent: Monday, November 05, 2001 8:13 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw
adjustment? and Rolled Ballscrews
Ballendo,
An EXCELLENT Post. Thank you.
A side note: A kerk salesman told me that they were the sole supplier
to Mcmaster for Rolled leadscrews and Anti-backlash nuts. Unfortunately,
Mcmaster does not carry Kerks "Good" Nuts just the cheapy ones. But,
I've seen them run on retail 20K routers day in and day out......
Chris L
Discussion Thread
ballendo@y...
2001-11-05 19:36:17 UTC
Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
motionin@a...
2001-11-05 20:05:07 UTC
Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
Chris L
2001-11-05 20:12:07 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
Tim Goldstein
2001-11-05 20:31:16 UTC
RE: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
Chris L
2001-11-05 20:48:54 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
ballendo@y...
2001-11-05 21:50:32 UTC
re: Ballscrews101
Dan Mauch
2001-11-06 07:13:14 UTC
RE: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
Henrik Olsson
2001-11-06 09:55:53 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews
ballendo@y...
2001-11-06 16:50:38 UTC
Ballscrews101 was Re: Ball screw adjustment? and Rolled Ballscrews