CAD CAM EDM DRO - Yahoo Group Archive

Re: What does Tool Radius Compensation do ?

on 1999-11-03 20:44:23 UTC
The first thing that comes to mind is when you program your part, you
program the actual part dimensions and then you use G41 or G42 to offset the
tool. That means that you can use any size tool that is convenient. Also you
can lie about the tool size, to the control, and compensate for tool wear or
deflection. You can tell the control that the tool is a .505 diameter and
then run a finish pass telling the control that the tool is .500 diameter.
The biggest advantage to diameter compensation is that you don't have to
repost the part every time you change a tool.
Darrell

----- Original Message -----
From: hansw <hansw@...>
To: <CAD_CAM_EDM_DRO@onelist.com>
Sent: Wednesday, November 03, 1999 8:32 PM
Subject: Re: [CAD_CAM_EDM_DRO] What does Tool Radius Compensation do ?


> From: hansw <hansw@...>
>
> My MAXNC software claims to have
>
> "TOOL RADIUS COMPENSATION "G" codes (G40, G41, G42)"
>
> and the Program by Doug Yeager "CNCPRO.EXE" does not have this. I
> prefer the Yeager program, it's much more logical in it's user
> interface.
>
> What is "TOOL RADIUS COMPENSATION " how can I see the difference
> between the results of with and without it...
>
> The kind of things I do, I have not seen any difference... Dumb Fat and
> Happy... but would like to understand this, what am I missing...
>
> Hans Wedemeyer
>
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems in the above catagories.
> To Unsubscribe, read archives, change to or from digest.
> Go to: http://www.onelist.com/isregistered.cgi
> Log on, and you will go to Member Center, and you can make changes there.
> For the FAQ, go to http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>

Discussion Thread

hansw 1999-11-03 20:32:16 UTC Re: What does Tool Radius Compensation do ? Darrell Gehlsen 1999-11-03 20:44:23 UTC Re: What does Tool Radius Compensation do ? Jon Anderson 1999-11-03 20:38:56 UTC Re: What does Tool Radius Compensation do ? hansw 1999-11-03 21:15:15 UTC Re: What does Tool Radius Compensation do ? hansw 1999-11-03 21:17:12 UTC Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-03 22:27:18 UTC Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-04 12:57:37 UTC Re: What does Tool Radius Compensation do ? Andrew Werby 1999-11-07 03:44:36 UTC Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-07 23:19:22 UTC Re: Re: What does Tool Radius Compensation do ? Andrew Werby 1999-11-08 02:20:45 UTC Re: What does Tool Radius Compensation do ? PTENGIN@x... 1999-11-08 11:50:35 UTC Re: Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-09 14:07:26 UTC Re: Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-09 14:10:44 UTC Re: Re: What does Tool Radius Compensation do ? Andrew Werby 1999-11-11 03:19:58 UTC Re: What does Tool Radius Compensation do ? Jon Elson 1999-11-11 12:17:50 UTC Re: Re: What does Tool Radius Compensation do ?