CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] More info on Smart Motors

on 2002-01-28 23:22:29 UTC
Methadras,

How much will ClemSoft be charging for their software once
it comes out of beta?

Bill




> okay, i've got a pretty good picture of what is going on with the
> smart motor...
>
> first of all its a brushless dc servo with integrated
> driver/controller on-board... i've talked to 6 users today and they
> said head wasn't a problem or an issue... the on-board controller has
> a thermal cut-off past 70 degrees C and they all said even thought
> hey push their motors hard, they've never been to hot to touch... 2
> guys i talked to are still using the same motors for the last 5 years
> without a hitch and all of the other guys are still using their
> motors for the last couple of years... so far, just from these guys
> i've talked to these motors are pretty tough nuggets that can handle
> the work...
>
> now here is the tricky part or maybe not so tricky depending on your
> point of view...
>
> you can serially daisy chain the motors together with rs-232 or rs-
> 485 or you can use animatics rail for serial I/O and power instead of
> the daisy chain method... this is a huge, huge plus for me because it
> nearly eliminates the need to purchase drivers, a box, all the
> wiring, and/or a controller... animatics sells their own proprietary
> VNC software for about $1000 and there is a third party developer
> that i've talked to personally at www.clemsoft.com that has written a
> really nice interface for the smart motor specifically... its still
> in beta and has a simulation mode built in... its written for windows
> 98/nt/2000 and i've downloaded it, but havn't run it yet... he is
> pretty dedicated to its development and he an i exchanged lots of
> ideas that he seemed fairly enthusiastic about... go check out the
> website for the software and email the guy about any info... well, i
> guess, that is if you really care...
>
> also he told me that the smart motors will and can use stepper motor
> instructions... here are his own words from an email exchange that he
> and i had and i must say its very promising and interesting;
>
> "In fact, did you know that any smartmotor can be configured for
> pulse/direction input? In this mode, neither the animatics vnc nor my
> software will work... but the huge amount of software written for
> steppers motors driven from the parallel port, will work better than
> ANY stepper ever thought it could work.... And I'm familiar with at
> least 10 people who have Dos/Windows based parallel port cnc
> solutions and are using it in this mode as well. One warning here...
> I doubt if you could get to 300-500 ipm with a parallel port driver
> system (since steppers can't do 5000 rpm like the smartmotors), but
> you definitely can with the SmartMotor."
>
> personally i think i've found my solution to my cnc retrofit... the
> software looks like it will do about 80% - 90% of what i want... the
> motors are completely in-line with what i've been looking for and i
> really don't have to worry about trying to find the magical black
> box/voodoo gear... i'm gonna take the plunge and keep you guys
> informed as to how it goes... wish me luck and as always i will
> entertain any questions or comments...
>
> Methadras
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

methadras 2002-01-28 18:29:51 UTC More info on Smart Motors William Scalione 2002-01-28 23:22:29 UTC Re: [CAD_CAM_EDM_DRO] More info on Smart Motors methadras 2002-01-28 23:37:30 UTC Re: More info on Smart Motors Fitch R. Williams 2002-01-29 04:40:17 UTC Re: [CAD_CAM_EDM_DRO] More info on Smart Motors