RE: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system

In a word "NO"
In fact the same code can be used to install on different computers.
All you need is a "VALID" code.

Garry

> oh... i was unclear. i meant INSTALL, not open, i seem to remember that the
> install required me getting a code from the company, didn't it? every time
> i reinstall? am i wrong.. it's been a while?---Dave L.
>
> -----Original Message-----
> From: rd@... [mailto:rd@...]
> Sent: Monday, February 25, 2002 3:49 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system
>
>
>
> Fred & Dave,
>
> Have to correct you there gents. In fairness to PTC Software, once you have
> the code and have it safely written down with all the other codes you have
> that is the end of it. I have installed it on my laptop, (designing Live
> Steam boilers at 36,000 ft) and also on my home PC using the same code in
> both cases.
>
> This was over a month ago and the only communication I have received from
> the software manufacturer since was a invitation to participate in a free
> on-line training presentation for this software last week. I did stay on
> for most of it but seeing as how there is 16 hours time difference between
> the vendor in the US and me in Western Australia, didn't quite make it to
> the end :o))
>
> Regards,
>
> Russell Dunn
> Perth
> Western Australia
> rd@...
> http://people.mydesk.net.au/~rd/index.html
>
> Date: Mon, 25 Feb 2002 15:23:59 -0500
> From: dlantz@...
> Subject: RE: Re: Ultimate free CAD system?
>
> my memory is a bit fuzzy on this (it was awhile ago) but i seem to remember
> having to get a registration code every time i load the software. now with
> windows... that can be every two weeks! if the company were to go out of
> bussiness, i would be out of luck.---Dave
>
> -----Original Message-----
> From: imserv@... [mailto:imserv@...]
> Sent: Monday, February 25, 2002 8:10 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: Ultimate free CAD system?
>
>
> --- In CAD_CAM_EDM_DRO@y..., dlantz@a... wrote:
> > i tried the pro/DEsk too, it seemed very powerfull also, however the
> > licencing thing was too constrictive for me
>
> Can you explain that a little more Dave? I am concerned that you
> noticed something that I might have missed. The only thing that stuck
> in my mind was restrictions to exporting to certain countries on the
> USA bad boy list.
>
>
> Best Regards,
>
> Fred Smith
> IMService
>
>
>
> --------------------------------------------------------------------
> mail2web - Check your email from the web at
> http://mail2web.com/ .
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> http://www.metalworking.com/news_servers.html
> http://www.metalworking.com/news_servers.html
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>