RE: [CAD_CAM_EDM_DRO] Closed loop stepper systems
Posted by
Dan Mauch
on 2002-03-13 08:17:39 UTC
The software. Most software will via the encoder determine if the
stepper is out of position, if so it will add steps within a certain
setup parameter to catch up. If it is too far beyond where it can catch
up then the program stops the motor so the operator can correct the
problem. That is how deskncrt and emc work.
-----Original Message-----
From: wamcdonald2002 [mailto:wamcdonald@...]
Sent: Tuesday, March 12, 2002 8:49 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Closed loop stepper systems
In a closed loop stepper system is it the responsibility of the
stepper driver or the software to correct for missing steps?
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
OFF Topic POSTS: General Machining
http://www.metalworking.com/news_servers.html
http://www.metalworking.com/news_servers.html
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
stepper is out of position, if so it will add steps within a certain
setup parameter to catch up. If it is too far beyond where it can catch
up then the program stops the motor so the operator can correct the
problem. That is how deskncrt and emc work.
-----Original Message-----
From: wamcdonald2002 [mailto:wamcdonald@...]
Sent: Tuesday, March 12, 2002 8:49 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Closed loop stepper systems
In a closed loop stepper system is it the responsibility of the
stepper driver or the software to correct for missing steps?
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
OFF Topic POSTS: General Machining
http://www.metalworking.com/news_servers.html
http://www.metalworking.com/news_servers.html
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
wamcdonald2002
2002-03-12 20:48:55 UTC
Closed loop stepper systems
Jon Elson
2002-03-12 23:15:11 UTC
Re: [CAD_CAM_EDM_DRO] Closed loop stepper systems
Gail & Bryan Harries
2002-03-13 07:40:42 UTC
RE: [CAD_CAM_EDM_DRO] Closed loop stepper systems
Dan Mauch
2002-03-13 08:17:39 UTC
RE: [CAD_CAM_EDM_DRO] Closed loop stepper systems
Jon Elson
2002-03-13 09:56:36 UTC
Re: [CAD_CAM_EDM_DRO] Closed loop stepper systems
Tim Goldstein
2002-03-13 21:05:26 UTC
RE: [CAD_CAM_EDM_DRO] Closed loop stepper systems