Re: Bipolar Driver with Unipolar stepper motor
Posted by
n4onl
on 2002-03-24 07:22:36 UTC
--- In CAD_CAM_EDM_DRO@y..., "Keith Sloan" <keith.sloan@u...> wrote:
You have 2 options when using Unipolar motors on Bipolar drives, Full
and Half Coil. Unipolar motors are wired with 2 coils in series with
a wire comming from the junction (tap) of the 2 coils (windings). If
you connect a Bipolar drive to the outside wires and use both coils
its called Full coil, if you use the center tap and one outside wire
(only one coil) its called Half coil. Half coil is preferred because
the inductance of the windings is 1/4th of what it is using Full
coil. Less inductance means higher top speed.
mike
> What is a half coil setup ?Hi Keith,
You have 2 options when using Unipolar motors on Bipolar drives, Full
and Half Coil. Unipolar motors are wired with 2 coils in series with
a wire comming from the junction (tap) of the 2 coils (windings). If
you connect a Bipolar drive to the outside wires and use both coils
its called Full coil, if you use the center tap and one outside wire
(only one coil) its called Half coil. Half coil is preferred because
the inductance of the windings is 1/4th of what it is using Full
coil. Less inductance means higher top speed.
mike
> Please could you elaborateJust use a
>
> > Message: 24
> > Date: Sat, 23 Mar 2002 20:24:45 -0700
> > From: "Tim Goldstein" <timg@k...>
> > Subject: RE: Re: Why is my feedrate slow with stepper motor
>
> > You don't need to replace the motors to use a bi-polar drive.
> > half coil setup with the bipolar drive.
>
> > Tim
> > [Denver, CO]
>
>
>
> Keith , Jenny & Family Sloan
> keith.sloan@u...
> http://web.ukonline.co.uk/keith.sloan/
>
>
> [Non-text portions of this message have been removed]
Discussion Thread
Keith Sloan
2002-03-24 05:00:16 UTC
Bipolar Driver with Unipolar stepper motor
dave_ace_me
2002-03-24 06:50:30 UTC
Re: Bipolar Driver with Unipolar stepper motor
n4onl
2002-03-24 07:22:36 UTC
Re: Bipolar Driver with Unipolar stepper motor
Tim Goldstein
2002-03-24 08:57:00 UTC
RE: [CAD_CAM_EDM_DRO] Bipolar Driver with Unipolar stepper motor
batwings@i...
2002-03-24 15:44:51 UTC
Chris Luebke rede ths plz
Chris L
2002-03-25 05:37:56 UTC
Re: [CAD_CAM_EDM_DRO] Chris Luebke rede ths plz
batwings@i...
2002-03-25 06:45:18 UTC
Re: [CAD_CAM_EDM_DRO] Chris Luebke rede ths plz
Chris L
2002-03-25 18:30:35 UTC
Re: [CAD_CAM_EDM_DRO] Chris Luebke rede ths plz
Carlos Guillermo
2002-03-25 21:50:45 UTC
RE: [CAD_CAM_EDM_DRO] Chris Luebke rede ths plz
CL
2002-03-26 05:56:38 UTC
Re: [CAD_CAM_EDM_DRO] Chris Luebke rede ths plz
batwings@i...
2002-03-26 05:57:01 UTC
Hi Carlos
batwings@i...
2002-03-26 05:57:04 UTC
Hi Chris
Carlos Guillermo
2002-03-26 15:06:20 UTC
RE: [CAD_CAM_EDM_DRO] Hi Carlos
batwings@i...
2002-03-27 05:27:30 UTC
RE: [CAD_CAM_EDM_DRO] Hi Carlos