CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]?

on 2002-04-12 08:13:35 UTC
How do you use comensation for the leadscrews?


----- Original Message -----
From: "Doug Fortune" <pentam@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, April 12, 2002 10:54 AM
Subject: Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]?


> carlcnc wrote:
> >
> > I had a guy ask me if I can make a router within .001 straightness
> > over 48", I am not sure this is possible with "normal" equipment.
>
> > Just to waste some time I checked my 5x8 in X.Y. best I can get
> > is +/- .005 over 6',using said straight edge.
>
> and I'll bet your steps are sub- 1/1000" !
>
> which means maybe you could meet that spec with software compensation
> on all the leadscrews. Note this means 3D compensation, which is
> a bit more involved (but not much) than just independent compensation
> of each leadscrew individually (ie the axes might not be orthogonal,
> so the 3D compensation would compensate for that).
>
> Doug Fortune
> http://www.cncKITS.com NEW-> 1KW power supply kits
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> .
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same memembers are there, for
OT subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

carlcnc 2002-04-12 05:57:46 UTC how straight is straight[rails]? Sven Peter 2002-04-12 07:14:48 UTC Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]? Doug Fortune 2002-04-12 07:57:46 UTC Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]? Scott Hendershot 2002-04-12 08:13:35 UTC Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]? dave_ace_me 2002-04-12 08:44:00 UTC Re: how straight is straight[rails]? carlcnc 2002-04-12 10:00:48 UTC Re: how straight is straight[rails]? Sven Peter 2002-04-12 11:16:46 UTC Re: [CAD_CAM_EDM_DRO] Re: how straight is straight[rails]? Jon Elson 2002-04-12 11:54:25 UTC Re: [CAD_CAM_EDM_DRO] how straight is straight[rails]? dave_ace_me 2002-04-12 17:01:46 UTC Re: how straight is straight[rails]? Paul Weber 2002-04-12 22:30:07 UTC Re: [CAD_CAM_EDM_DRO] Re: how straight is straight[rails]? Elliot Burke 2002-04-13 01:26:24 UTC re:Re: how straight is straight[rails]?