Re: Brushless servo drive - Cheap Solution?????
Posted by
mariss92705
on 2002-04-19 18:15:59 UTC
Jon,
The G420 is step and direction input. Same specs as the G320
otherwise.
Next in the hopper for new drives is is an evisceration of the
step/direction interface which will be replaced with a +/-10V, 0-5V
interface. It will be jumperable for current mode, voltage mode or IR
compensated mode operation. In otherwords, a "classic" servoamplifier
rather than a complete drive. The model numbers have not yet been
picked.
Mariss
The G420 is step and direction input. Same specs as the G320
otherwise.
Next in the hopper for new drives is is an evisceration of the
step/direction interface which will be replaced with a +/-10V, 0-5V
interface. It will be jumperable for current mode, voltage mode or IR
compensated mode operation. In otherwords, a "classic" servoamplifier
rather than a complete drive. The model numbers have not yet been
picked.
Mariss
--- In CAD_CAM_EDM_DRO@y..., Jon Elson <elson@p...> wrote:
> mariss92705 wrote:
>
> > Joe,
> >
> > I get the G420 prototype boards back tomorrow. The G420 will be a
3-
> > phase brushless DC servodrive. The same specs will apply to it as
for
> > the G320. I will know by next week if it runs OK.
>
> Can you give us a refresher on the type of servo drive this is?
Does it
> take step inputs, or some form of velocity command?
>
> Jon
Discussion Thread
onecooltoolfool
2002-04-17 11:51:13 UTC
Brushless servo drive - Cheap Solution?????
mariss92705
2002-04-19 02:37:04 UTC
Re: Brushless servo drive - Cheap Solution?????
Jon Elson
2002-04-19 13:53:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
mariss92705
2002-04-19 18:15:59 UTC
Re: Brushless servo drive - Cheap Solution?????
Matt Shaver
2002-04-19 18:24:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
mariss92705
2002-04-19 19:33:52 UTC
Re: Brushless servo drive - Cheap Solution?????
Brian
2002-04-20 11:14:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
mariss92705
2002-04-20 12:02:23 UTC
Re: Brushless servo drive - Cheap Solution?????
William Scalione
2002-04-20 12:12:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
Carol & Jerry Jankura
2002-04-20 18:38:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
Jon Elson
2002-04-20 20:26:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
Tim Goldstein
2002-04-20 20:33:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
Jon Elson
2002-04-20 21:13:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????
Jon Elson
2002-04-21 10:10:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Brushless servo drive - Cheap Solution?????