Re: [CAD_CAM_EDM_DRO] BDI Again

Gene

OK then, Are you running freqmod? if so, then I think you need to
increase the "period" value in the ini file. Do it in steps until you just
get to where the mouse is resposnsive enough for you. Write down
your original value in case this does not work, I'm no expert.

You could also comment out the period parameter in the ini file and
switch to steppermod. It's a lot easier to get going, but the pulse train
can be a bit ragged. I am using steppermod, but the Gecko G3x0 servo
drives I have don't care about a ragged pulse train.

Bill

----- Original Message -----
From: "Gene" <capper@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, May 25, 2002 12:00 AM
Subject: Re: [CAD_CAM_EDM_DRO] BDI Again


> Its fine on the desktop, only with EMC running it acts up.
>
> William Scalione wrote:
> >
> > > Well I reinstalled the BDI and everything is working again but the
mouse
> > > seems sluggish and blinks on and off ,very annoying. Is there a place
to
> > > adjust mouse settings?
> > >
> >
> > Gene,
> >
> > Is the mouse sluggish only when EMC is running or all the time,
> > ie. is it sluggish when running the K desktop?
> >
> > Bill
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
> >
> > Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> > Moderator: jmelson@... timg@... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>