RE: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Posted by
Carol & Jerry Jankura
on 2002-06-04 17:24:29 UTC
Mark:
It's not a matter of "steps per inch" but rather "steps per second." If you
suspect that you're in a situation where the computer can't keep up, you can
slow down your maximum pulse rate or your feed rate and see what happens.
Although I haven't played with either CNCPro or MaxNC, I doubt that it's the
processor. The 585 is equivalent to a Pentium, give or take a little, right?
If so, it should not be the bottleneck when running DOS programs.
-- Jerry
|Morning all,
|Well I am still having a little bit of trouble. With Cncpro
|evaluation I have everything running spot on, but when I try and use
|Maxnc and get all the calibrations correct it will only process the
|first couple of lines and the program will lock up . Is it because
|there are too many steps per inch and the computer cannot cope?( it
|is only a 585 dx 100) It will fast jog and all ok! The only way I can
|get the demo programs to run after that is to reload the software and
|then it goes back to the default settings and will run all the
|programs but not at the correct calibrations! I have to change them
|again and then maxnc locks up again!. There are 20,000 steps per inch
|in both the x & y and an incredible 45,134 per inch in the z axis!
|Rmember it is ok with these in CNCPRO.Help anyone?
|Mark
|
|
|Addresses:
|FAQ: http://www.ktmarketing.com/faq.html
|FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
|OFF Topic POSTS: General Machining
|If you wish to post on unlimited OT subjects goto:
|aol://5863:126/rec.crafts.metalworking or go thru Google.com to
|reach it if you have trouble.
|http://www.metalworking.com/news_servers.html
|
|http://groups.yahoo.com/group/jobshophomeshop I consider this as
|a sister site to the CCED group, as many of the same members are
|there, for OT subjects, that are not allowed on the CCED list.
|
|
|
|Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
|Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
|Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
|List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
|Moderator: jmelson@... timg@... [Moderator]
|URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
|bill,
|List Mom
|List Owner
|
|
|
|Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
It's not a matter of "steps per inch" but rather "steps per second." If you
suspect that you're in a situation where the computer can't keep up, you can
slow down your maximum pulse rate or your feed rate and see what happens.
Although I haven't played with either CNCPro or MaxNC, I doubt that it's the
processor. The 585 is equivalent to a Pentium, give or take a little, right?
If so, it should not be the bottleneck when running DOS programs.
-- Jerry
|Morning all,
|Well I am still having a little bit of trouble. With Cncpro
|evaluation I have everything running spot on, but when I try and use
|Maxnc and get all the calibrations correct it will only process the
|first couple of lines and the program will lock up . Is it because
|there are too many steps per inch and the computer cannot cope?( it
|is only a 585 dx 100) It will fast jog and all ok! The only way I can
|get the demo programs to run after that is to reload the software and
|then it goes back to the default settings and will run all the
|programs but not at the correct calibrations! I have to change them
|again and then maxnc locks up again!. There are 20,000 steps per inch
|in both the x & y and an incredible 45,134 per inch in the z axis!
|Rmember it is ok with these in CNCPRO.Help anyone?
|Mark
|
|
|Addresses:
|FAQ: http://www.ktmarketing.com/faq.html
|FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
|
|OFF Topic POSTS: General Machining
|If you wish to post on unlimited OT subjects goto:
|aol://5863:126/rec.crafts.metalworking or go thru Google.com to
|reach it if you have trouble.
|http://www.metalworking.com/news_servers.html
|
|http://groups.yahoo.com/group/jobshophomeshop I consider this as
|a sister site to the CCED group, as many of the same members are
|there, for OT subjects, that are not allowed on the CCED list.
|
|
|
|Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
|Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
|Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
|List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
|Moderator: jmelson@... timg@... [Moderator]
|URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
|bill,
|List Mom
|List Owner
|
|
|
|Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
|
|
|
Discussion Thread
markpowerplus
2002-06-04 12:23:28 UTC
Maxnc and Gecko 201's
Carey L. Culpepper
2002-06-04 12:31:54 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
markpowerplus
2002-06-04 12:49:11 UTC
Re: Maxnc and Gecko 201's
Carey L. Culpepper
2002-06-04 12:54:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Maxnc and Gecko 201's
Alan Marconett KM6VV
2002-06-04 14:21:52 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Carol & Jerry Jankura
2002-06-04 17:24:29 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
John
2002-06-04 19:58:03 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Alan Marconett KM6VV
2002-06-04 20:26:19 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
bsptrades
2002-06-05 00:22:51 UTC
Re: sherline and Gecko's