Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Posted by
John
on 2002-06-04 19:58:03 UTC
I remember asking whether it'd be worth putting Gecko's on a Sherline a good
long while back and someone said it'd be quite pointless considering the
size of the travel and the screw properties. Like 'Going first class on a
second class machine'. I understand a lot more about CNC now but could
someone be helpful and remind me why this is the case?
Thanks,
John H.
P.S. I'm talking steppers here! : )
you have trouble.
subjects, that are not allowed on the CCED list.
long while back and someone said it'd be quite pointless considering the
size of the travel and the screw properties. Like 'Going first class on a
second class machine'. I understand a lot more about CNC now but could
someone be helpful and remind me why this is the case?
Thanks,
John H.
P.S. I'm talking steppers here! : )
> Mark:you
>
> It's not a matter of "steps per inch" but rather "steps per second." If
> suspect that you're in a situation where the computer can't keep up, youcan
> slow down your maximum pulse rate or your feed rate and see what happens.the
>
> Although I haven't played with either CNCPro or MaxNC, I doubt that it's
> processor. The 585 is equivalent to a Pentium, give or take a little,right?
> If so, it should not be the bottleneck when running DOS programs.aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
>
> -- Jerry
>
> |Morning all,
> |Well I am still having a little bit of trouble. With Cncpro
> |evaluation I have everything running spot on, but when I try and use
> |Maxnc and get all the calibrations correct it will only process the
> |first couple of lines and the program will lock up . Is it because
> |there are too many steps per inch and the computer cannot cope?( it
> |is only a 585 dx 100) It will fast jog and all ok! The only way I can
> |get the demo programs to run after that is to reload the software and
> |then it goes back to the default settings and will run all the
> |programs but not at the correct calibrations! I have to change them
> |again and then maxnc locks up again!. There are 20,000 steps per inch
> |in both the x & y and an incredible 45,134 per inch in the z axis!
> |Rmember it is ok with these in CNCPRO.Help anyone?
> |Mark
> |
> |
> |Addresses:
> |FAQ: http://www.ktmarketing.com/faq.html
> |FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> |
> |OFF Topic POSTS: General Machining
> |If you wish to post on unlimited OT subjects goto:
> |aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> |reach it if you have trouble.
> |http://www.metalworking.com/news_servers.html
> |
> |http://groups.yahoo.com/group/jobshophomeshop I consider this as
> |a sister site to the CCED group, as many of the same members are
> |there, for OT subjects, that are not allowed on the CCED list.
> |
> |
> |
> |Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> |Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> |Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> |List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> |Moderator: jmelson@... timg@... [Moderator]
> |URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> |bill,
> |List Mom
> |List Owner
> |
> |
> |
> |Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> |
> |
> |
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
you have trouble.
> http://www.metalworking.com/news_servers.htmlsister site to the CCED group, as many of the same members are there, for OT
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
markpowerplus
2002-06-04 12:23:28 UTC
Maxnc and Gecko 201's
Carey L. Culpepper
2002-06-04 12:31:54 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
markpowerplus
2002-06-04 12:49:11 UTC
Re: Maxnc and Gecko 201's
Carey L. Culpepper
2002-06-04 12:54:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Maxnc and Gecko 201's
Alan Marconett KM6VV
2002-06-04 14:21:52 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Carol & Jerry Jankura
2002-06-04 17:24:29 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
John
2002-06-04 19:58:03 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
Alan Marconett KM6VV
2002-06-04 20:26:19 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc and Gecko 201's
bsptrades
2002-06-05 00:22:51 UTC
Re: sherline and Gecko's