CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] checking parallel port

Posted by Dan Mauch
on 2002-06-07 06:55:38 UTC
The +5 from the signal source (PC)is required to be connected to pin 10
not from the power supply. Use a floppy drive connector from your pc and
locate the Red wire. This is +5 connect that to pin 10.
Dan

-----Original Message-----
From: hugo_cnc [mailto:Hwatering@...]
Sent: Friday, June 07, 2002 3:49 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] checking parallel port

Hi all,

Is there a way to check if there coming a signal out of the parallel
port, with something like a voltage/amperage/resistance meter. I use
a geckodrive 201, a 1300 oz/in motor and 24V 2A power supply. The
power supply is just for testing, could it be that the power supply
is not powerful enough to move the motor at all. I use the same power
supply which also have a +5V terminal, to connect to the common
(terminal 10) of the geckodrive, the ground is connected to the
ground (terminal 1). I have tried different controllers Desknc,
Master5 and Cncpro, but the motor won't move.
I use a standard parallel cable but the numbering is a bit different
that what is described in DeskNC. If you look at the pins numbers,
pin one is upper left instead of upper right (the wide side above),
could this be part of the problem.
Thanks


Hugo



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.



Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner



Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/

Discussion Thread

hugo_cnc 2002-06-07 03:49:03 UTC checking parallel port Bob Campbell 2002-06-07 05:57:37 UTC RE: [CAD_CAM_EDM_DRO] checking parallel port Dan Mauch 2002-06-07 06:55:38 UTC RE: [CAD_CAM_EDM_DRO] checking parallel port Alan Marconett KM6VV 2002-06-07 11:03:57 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port Tim Goldstein 2002-06-07 12:45:17 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port hugo_cnc 2002-06-07 14:53:37 UTC Re: checking parallel port JanRwl@A... 2002-06-07 20:35:09 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port JanRwl@A... 2002-06-07 20:55:47 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port Jon Elson 2002-06-07 22:07:13 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port JanRwl@A... 2002-06-07 22:40:42 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port Jon Elson 2002-06-08 09:41:43 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port Alan Marconett KM6VV 2002-06-08 10:46:14 UTC Re: [CAD_CAM_EDM_DRO] checking parallel port