Re: vexta steppers
Posted by
mariss92705
on 2002-06-12 11:12:53 UTC
Kenneth,
The motor I ran tests on is a Sanyo Denki "Step-Syn" 103H7126, a 2A
per phase, 180 in-oz size 23 motor. The motor torque was:
0 to 2,500 full steps/sec (0 to 750RPM) 180 in-oz
5,000 full steps/sec (1,500RPM) 85 in-oz
10,000 full steps/sec (3,000RPM) 35 in-oz
20,000 full steps/sec (6,000RPM) 15 in-oz
No-load stall 34,000 full steps/sec (10,200RPM)
This motor is a "square" motor, not the older round motor. I assume
yours is a round one because I could find no data on Sanyo Denki site
for that number.
Mariss
The motor I ran tests on is a Sanyo Denki "Step-Syn" 103H7126, a 2A
per phase, 180 in-oz size 23 motor. The motor torque was:
0 to 2,500 full steps/sec (0 to 750RPM) 180 in-oz
5,000 full steps/sec (1,500RPM) 85 in-oz
10,000 full steps/sec (3,000RPM) 35 in-oz
20,000 full steps/sec (6,000RPM) 15 in-oz
No-load stall 34,000 full steps/sec (10,200RPM)
This motor is a "square" motor, not the older round motor. I assume
yours is a round one because I could find no data on Sanyo Denki site
for that number.
Mariss
--- In CAD_CAM_EDM_DRO@y..., KenMa <gwtech@m...> wrote:
> Hi Mariss,
>
> I had collected some 3 stacks 6 wire Sanyo Denki motors type
> 103-746-1611 rated at 6.3VDC 1.9ADC. Are these the ones you
mentioned
> in your message? What kind of torque can I expect from these motor
> with your Gecko drivers?
>
> Kenneth
>
>
> >Message: 10
> > Date: Wed, 12 Jun 2002 05:39:08 -0000
> > From: "mariss92705" <mariss92705@y...>
> >Subject: Re: vexta steppers
> >
> >Hi,
> >
> >Sanyo Denki motors are inexpensive (<$100) and are among the best
> >motors I have ever tested, particularly the 103 series. The 2 amp
> >version eaisily spins up to over 6,000 RPM no-load and outputs
100W
> >at 60VDC. They are also exceptionally linear, making them
excellent
> >microstepping candidates. I measured the ratio between the
smallest
> >microstep to the biggest at 1:1.1, meaning the motor linearity is
> >about 1%. My 2 cent's worth.
> >
> >Mariss
> >
> >--- In CAD_CAM_EDM_DRO@y..., "markpowerplus" <mabw@b...> wrote:
> >> Morning all,
> >> Does anyone know a good place to buy Vexta stepper motors from?
> >Like
> >> some where reasonable priced (read cheap)!
> >> thanks
> >> Mark
Discussion Thread
markpowerplus
2002-06-11 14:44:02 UTC
vexta steppers
JanRwl@A...
2002-06-11 16:26:14 UTC
Re: [CAD_CAM_EDM_DRO] vexta steppers
markpowerplus
2002-06-11 17:28:48 UTC
Re: vexta steppers
bsptrades
2002-06-11 18:53:50 UTC
Re: vexta steppers
mariss92705
2002-06-11 22:39:11 UTC
Re: vexta steppers
KenMa
2002-06-12 10:00:35 UTC
Re: vexta steppers
mariss92705
2002-06-12 11:12:53 UTC
Re: vexta steppers
paul_alz
2002-06-12 11:31:01 UTC
Re: vexta steppers
gwtech_yh
2002-06-12 11:42:40 UTC
Re: vexta steppers
paul_alz
2002-06-12 14:12:49 UTC
Re: vexta steppers
KenMa
2002-06-13 15:15:32 UTC
Re: vexta steppers