Re: [CAD_CAM_EDM_DRO] Increasing DRO resolution
Posted by
w.higdon@a...
on 2002-10-20 08:25:25 UTC
Paul,
To answer the question of using a mechanical means to
increase encoder resolution, I have seen it used both
with encoders and the older syncro's to increase
resolution. Toothed timing belts aren't as compact as
gears, but they are easier to setup and not have a lot
of backlash. Yes I know they make antibacklash gears,
however they are more expensive and harder to set up.
Bill Higdon
To answer the question of using a mechanical means to
increase encoder resolution, I have seen it used both
with encoders and the older syncro's to increase
resolution. Toothed timing belts aren't as compact as
gears, but they are easier to setup and not have a lot
of backlash. Yes I know they make antibacklash gears,
however they are more expensive and harder to set up.
Bill Higdon
> This has probably been dealt with before but I can't find it in the
> archive.
> It has been said on this group that encoders should, ideally, have
> a resolution 10 times greater than that which you wish to display.
> Therefore to display measurements down to 0.0005" (� thou.) the
> resolution of the decoder would have to detect movement of 0.00005".
> Art Eckstein shows on his webpage http://ns1.dicomm.net/~axtein/ how
> he used mechanical advantage to double the resolution of his system
> when using rotary encoders.
> > Paul
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you
> have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a sister site
> to the CCED group, as many of the same members are there, for OT subjects, that
> are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T
> POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
paul_norton2001
2002-10-20 03:57:05 UTC
Increasing DRO resolution
w.higdon@a...
2002-10-20 08:25:25 UTC
Re: [CAD_CAM_EDM_DRO] Increasing DRO resolution
Jon Elson
2002-10-20 21:25:40 UTC
Re: [CAD_CAM_EDM_DRO] Increasing DRO resolution
mayfieldtm
2002-10-21 08:39:34 UTC
Re: Increasing DRO resolution