Re: [CAD_CAM_EDM_DRO] Shared Direction pins vs dedicated Direction pins
Posted by
Chris L
on 2003-02-09 19:45:56 UTC
Doug Fortune wrote:
elsewhere, correct ? Like some of those "daisychain" drivers that run on
Cat5 or something ? As I recall, I remember always noticing that the
fellows selling them were not supplying and CNC type software. So I
always looked away. I can see and understand what you mean though now,
and yes, it would appear that it would be a benefit to design around that.
In regards timing issue, Did you know that some MicroK drives need 60uS
for Dir change ? One could almost take nap in there somewhere !
Makes for a slow flatbed Router! But in Fairness, not so bad for a
Sherline Mill though.......
Thanks again,
Chris L
>In other words, you could have many (50 channels in this example)I get it now Doug, and If I'm really getting it, I'd say I've seen this
>sharing a common direction pin, and neither the motors nor the human
>would be able to detect any measurable difference. However the Geckos
>(much as I like them) have a hold-time constraint on the Direction line
>which precludes their use in a "shared-direction" scheme.
>
elsewhere, correct ? Like some of those "daisychain" drivers that run on
Cat5 or something ? As I recall, I remember always noticing that the
fellows selling them were not supplying and CNC type software. So I
always looked away. I can see and understand what you mean though now,
and yes, it would appear that it would be a benefit to design around that.
In regards timing issue, Did you know that some MicroK drives need 60uS
for Dir change ? One could almost take nap in there somewhere !
Makes for a slow flatbed Router! But in Fairness, not so bad for a
Sherline Mill though.......
Thanks again,
Chris L
Discussion Thread
Doug Fortune
2003-02-09 18:45:18 UTC
Shared Direction pins vs dedicated Direction pins
Chris L
2003-02-09 19:45:56 UTC
Re: [CAD_CAM_EDM_DRO] Shared Direction pins vs dedicated Direction pins
Bernard R <bwjarandall@c...
2003-02-09 20:15:30 UTC
Re: Shared Direction pins vs dedicated Direction pins
Mariss Freimanis <mariss92705@y...
2003-02-09 20:19:16 UTC
Re: Shared Direction pins vs dedicated Direction pins
Bernard R <bwjarandall@c...
2003-02-09 20:58:07 UTC
Re: Shared Direction pins vs dedicated Direction pins
Doug Fortune
2003-02-09 21:34:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shared Direction pins vs dedicated Direction pins
ballendo <ballendo@y...
2003-02-12 06:52:09 UTC
Re: Shared Direction pins vs dedicated Direction pins
ballendo <ballendo@y...
2003-02-12 06:53:36 UTC
Re: Shared Direction pins vs dedicated Direction pins
Tony Jeffree
2003-02-12 07:01:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shared Direction pins vs dedicated Direction pins
alex
2003-02-12 07:31:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shared Direction pins vs dedicated Direction pins
Mariss Freimanis <mariss92705@y...
2003-02-12 07:48:51 UTC
Re: Shared Direction pins vs dedicated Direction pins
ballendo <ballendo@y...
2003-02-12 08:22:34 UTC
Re: Shared Direction pins vs dedicated Direction pins
ballendo <ballendo@y...
2003-02-12 08:26:14 UTC
Re: Shared Direction pins vs dedicated Direction pins
ccq@x...
2003-02-12 11:07:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shared Direction pins vs dedicated
Andre' Blanchard <andre_54005@y...
2003-02-12 11:11:38 UTC
Re: Shared Direction pins vs dedicated Direction pins
alex
2003-02-12 13:50:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Shared Direction pins vs dedicated Direction pins