Re: It's Alive!
Posted by
jmkasunich <jmkasunich@y...
on 2003-02-25 11:30:16 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Mariss Freimanis
<mariss92705@y...>" <mariss92705@y...> wrote:
<grin>
FETs, etc,? Hand insert and solder?
John Kasunich
<mariss92705@y...>" <mariss92705@y...> wrote:
> John,Doesn't all the bare green on the bottom drive you nuts?
>
> 1) Manual stencil machine. No point for an automated one
> because this step takes only 30 seconds.
>
> 2) I use top side SMT only. Doing top and bottom triples
> the process time (top mount, reflow, glue dispense, bottom
> mount, reflow again). Nightmares are made that way; parts
> falling off in the oven, a "glue accident" in the machine, etc.
>
<grin>
> 3) The oven is an Essemtec 6 zone IR oven, (preheat, soakWhat about thru-hole parts - connectors, electrolytic caps,
> and reflow both top and bottom). About 3 minutes from the
> goezinta to the goezouta.
>
FETs, etc,? Hand insert and solder?
John Kasunich
Discussion Thread
Mariss Freimanis <mariss92705@y...
2003-02-24 20:52:34 UTC
It's Alive!
Peter Homann
2003-02-24 20:59:00 UTC
RE: [CAD_CAM_EDM_DRO] It's Alive!
Monte Westlund <montejw@e...
2003-02-25 06:04:03 UTC
Re: It's Alive!
jmkasunich <jmkasunich@y...
2003-02-25 06:56:50 UTC
Re: It's Alive!
James Cullins
2003-02-25 07:07:23 UTC
Re: [CAD_CAM_EDM_DRO] It's Alive!
Mariss Freimanis <mariss92705@y...
2003-02-25 10:52:13 UTC
Re: It's Alive!
jmkasunich <jmkasunich@y...
2003-02-25 11:30:16 UTC
Re: It's Alive!
James Cullins
2003-02-25 11:53:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: It's Alive!
Mariss Freimanis <mariss92705@y...
2003-02-25 12:35:16 UTC
Re: It's Alive!
Mariss Freimanis <mariss92705@y...
2003-02-25 12:36:36 UTC
Re: It's Alive!
Dave Lantz
2003-02-25 12:37:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: It's Alive!
Tony Jeffree
2003-02-25 12:48:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: It's Alive!
Mariss Freimanis <mariss92705@y...
2003-02-25 13:46:18 UTC
Re: It's Alive!
Raymond Heckert
2003-02-26 18:12:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: It's Alive!
Raymond Heckert
2003-02-26 18:14:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: It's Alive!
Vince Negrete
2003-02-26 20:50:25 UTC
Re: [CAD_CAM_EDM_DRO] It's Alive!
jmkasunich <jmkasunich@y...
2003-02-27 05:51:22 UTC
Re: It's Alive!