CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew

on 2003-05-15 11:42:40 UTC
>
>
>snipped alot of stuff<<<<<<<<<<<<
>
I have to disagree here slightly there is not a huge difference in
pricing between ACME thredad and all thread. You end up spending a
greatdeal of money that you wouldn't otherwise spend if you just upgrade
to the ACME in the first place.

Also there are design points where even the tought of designing for the
ultimate makes the project impractical. Yes these are often home
projects but it isn't unheard of in an industrial situation.

So the reality is that the individual has to make due with what he can
justify. It does not hurt though to understand that ACME screws are
not that much out of line.

Thanks
dave

>
>My advice stays the same. DESIGN with the ultimate in mind (ie:
>leave the space for it), but TEST with cheap crap(cheap allthread),
>and INSTALL the best cost/function you can get away with.
>
>As a note here, I used some cheap all-thread on a table and found
>mistakes in the table that would have prevented me from using the
>ball screws I so desired. the $10.00 for the screw was well worth it.
>
>
>
>
>
>
>
>
>

Discussion Thread

cadcamclub 2003-05-14 17:07:14 UTC leadscrew, acme screw, threaded rod, ballscrew Ross 2003-05-14 17:16:44 UTC Re: leadscrew, acme screw, threaded rod, ballscrew cadcamclub 2003-05-14 17:47:48 UTC Re: leadscrew, acme screw, threaded rod, ballscrew Ross 2003-05-14 18:17:02 UTC Re: leadscrew, acme screw, threaded rod, ballscrew turbulatordude 2003-05-14 19:57:45 UTC ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew caudlet 2003-05-14 19:58:25 UTC Re: leadscrew, acme screw, threaded rod, ballscrew Chris L 2003-05-14 20:31:45 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew C.S. Mo 2003-05-14 20:40:51 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew turbulatordude 2003-05-15 06:45:15 UTC ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew Ross 2003-05-15 07:23:52 UTC ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew David A. Frantz 2003-05-15 09:07:43 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew Chris L 2003-05-15 10:39:21 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew Chris L 2003-05-15 11:14:14 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew David A. Frantz 2003-05-15 11:42:40 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew dcdziner 2003-05-15 17:45:19 UTC Re: [CAD_CAM_EDM_DRO] ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew turbulatordude 2003-05-16 08:22:01 UTC Beginners screws ( was ACME ( was Re: leadscrew, turbulatordude 2003-05-16 08:27:17 UTC ACME ( was Re: leadscrew, acme screw, threaded rod, ballscrew