Re: [CAD_CAM_EDM_DRO] MPJA 24v 10amp Transformers - Anyone actually using it?
Posted by
paul.beckingham@j...
on 2003-05-17 06:43:50 UTC
Hi Shawn,
yes, I've used this transformer on the hobbycnc machine. The
unloaded voltage is at least 34vdc, which I thought was perilously
close to the max voltage for the drivers (35v), so I have a switch on
the primary, and start on the 220v tap, which precharges the big
capacitor to about 17v, and allows a low-heat dry run. Then when
full power is needed, I switch to the 110v tap, with the drivers
already on. With the coils loading the cap, the voltage doesn't rise
above 34v, so I feel this is safer. It looks like a good quality
transformer, 10amps is enough for me, and the price is good!
Regards, Paul
yes, I've used this transformer on the hobbycnc machine. The
unloaded voltage is at least 34vdc, which I thought was perilously
close to the max voltage for the drivers (35v), so I have a switch on
the primary, and start on the 220v tap, which precharges the big
capacitor to about 17v, and allows a low-heat dry run. Then when
full power is needed, I switch to the 110v tap, with the drivers
already on. With the coils loading the cap, the voltage doesn't rise
above 34v, so I feel this is safer. It looks like a good quality
transformer, 10amps is enough for me, and the price is good!
Regards, Paul
On 15 May 2003, at 22:17, shawnusa2002 wrote:
> I was wanting to know if anyone has built and using the Trnasformers
> sold by MPJA ((2) 24v 10amp #7846)in the series configuration like
> shown in Jerries schematic in the files section. I have read
> numorous postings on here from past and got lost in finding out if
> anyone actually built one and is using it with the Geckos. Did the
> final product actually exceed the voltage limits of the Gecko's?
>
> Comments please. What end results did you get? Are you pleased with
> the results? I'm getting ready to make the plunge and buy the parts
> for this schematic.
>
> Aside from this anyone have a good source otherwise for a Transfomer
> that will produce +/-60vdc 5-10amp as a alternative to going the
> series conecttion rought.
>
> Appricate to commentary.
>
> Shawn
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
Paul Beckingham
Discussion Thread
shawnusa2002
2003-05-15 15:19:47 UTC
MPJA 24v 10amp Transformers - Anyone actually using it?
colin_jet
2003-05-15 16:20:57 UTC
Re: MPJA 24v 10amp Transformers - Anyone actually using it?
John Guenther
2003-05-15 16:41:33 UTC
RE: [CAD_CAM_EDM_DRO] MPJA 24v 10amp Transformers - Anyone actually using it?
vrsculptor
2003-05-15 19:25:46 UTC
Re: MPJA 24v 10amp Transformers - Anyone actually using it?
Alan Marconett KM6VV
2003-05-16 09:14:46 UTC
Re: MPJA 24v 10amp Transformers - Anyone actually using it?
paul.beckingham@j...
2003-05-17 06:43:50 UTC
Re: [CAD_CAM_EDM_DRO] MPJA 24v 10amp Transformers - Anyone actually using it?
turbulatordude
2003-05-17 06:59:42 UTC
Re: MPJA 24v 10amp Transformers - Anyone actually using it?