Re: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Posted by
Jon Elson
on 2003-06-08 11:53:14 UTC
Tim Goldstein wrote:
Yes your motors will suffer major heating problems set up that way. If
motors, and he doesn't expect cutting loads, apparently.
Jon
Yes your motors will suffer major heating problems set up that way. If
>you want to run at that low an RPM you need to use steppers.I think not, as his expected load is 2.8% of the peak. These are very large
>
motors, and he doesn't expect cutting loads, apparently.
Jon
Discussion Thread
etauch
2003-06-07 12:02:26 UTC
hot servo motors, heatsinks??
Mariss Freimanis
2003-06-07 17:05:34 UTC
Re: hot servo motors, heatsinks??
David A. Frantz
2003-06-07 18:14:27 UTC
Re: [CAD_CAM_EDM_DRO] hot servo motors, heatsinks??
Jon Elson
2003-06-07 22:16:09 UTC
Re: [CAD_CAM_EDM_DRO] hot servo motors, heatsinks??
etauch
2003-06-08 01:07:22 UTC
Re: hot servo motors, heatsinks??...maybe another redesign
Kim Lux
2003-06-08 09:45:40 UTC
CNC Servo motor gear ratio: overheating. EMC step rate. Table speed
Tim Goldstein
2003-06-08 09:58:49 UTC
RE: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Jon Elson
2003-06-08 11:53:14 UTC
Re: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Tim Goldstein
2003-06-08 12:07:05 UTC
RE: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-08 16:02:14 UTC
RE: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-08 16:12:06 UTC
Re: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-08 16:17:04 UTC
RE: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
mmurray701
2003-06-08 18:54:42 UTC
Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Mariss Freimanis
2003-06-08 19:05:31 UTC
Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Jon Elson
2003-06-08 21:11:14 UTC
Re: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
mmurray701
2003-06-09 05:53:44 UTC
Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-09 06:34:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-09 06:39:43 UTC
Re: [CAD_CAM_EDM_DRO] CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
deanc500
2003-06-09 16:33:36 UTC
Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
Kim Lux
2003-06-09 21:57:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
deanc500
2003-06-09 22:28:42 UTC
Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed
etauch
2003-06-11 15:51:41 UTC
Re: CNC Servo motor gear ratio: overheating...perplexing
David A. Frantz
2003-06-12 08:09:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Servo motor gear ratio: overheating...perplexing