Posts by deanc500

deanc500 2002-01-30 09:22:02 UTC Re: Threaded Rod/Cable Driven Encoders deanc500 2002-02-25 22:06:46 UTC Re: Advice sought re: driver interface deanc500 2002-03-06 14:04:52 UTC Re: Limit and Homing switches Over 2200 members today deanc500 2002-03-09 08:54:06 UTC Re: stepper driver deanc500 2002-03-13 20:04:23 UTC Re: How bout this idea?? deanc500 2002-03-13 20:53:12 UTC Re: How bout this idea?? deanc500 2002-03-17 21:21:22 UTC Re: +5V deanc500 2002-03-18 21:11:51 UTC Re: Building A Cheap DRO deanc500 2002-09-25 06:31:57 UTC What do you think of this mill? deanc500 2002-09-25 06:34:28 UTC What do you think of this mill? deanc500 2002-09-30 12:57:22 UTC How to raise and lower head without losing x and y? deanc500 2002-10-09 22:19:36 UTC Re: Heck of a time tuning servo motors. deanc500 2002-10-18 13:38:13 UTC cant see parallel port from dos deanc500 2002-10-18 13:44:12 UTC Re: cant see parallel port from dos - forgot to mention... deanc500 2002-10-18 15:31:07 UTC Re: cant see parallel port from dos - forgot to mention... deanc500 2002-10-18 16:38:33 UTC Re: cant see parallel port from dos - forgot to mention... deanc500 2002-10-18 17:42:42 UTC cant see parallel port from dos- found it! deanc500 2002-10-22 11:02:53 UTC Re: Ideas for matching drives on a YY axis design? deanc500 2002-10-23 17:23:38 UTC 25Khz glitch ? (was Re: Ideas for matching drives on a YY axis design? deanc500 2002-10-23 20:54:03 UTC Re: YES !!! One axis working under TurboCNC, a few questions now.. deanc500 2002-11-02 13:10:07 UTC Re: Pre-wired drive unit deanc500 2002-11-13 09:35:27 UTC need simple software to run single axis - dividing head deanc500 2002-11-20 11:55:35 UTC Re: Encoders deanc500 2002-11-20 12:10:02 UTC Re: CNC Painting deanc500 2002-11-21 08:34:18 UTC Re: Home cnc project deanc500 2002-11-21 23:38:13 UTC Re: Need indexing head software.... deanc500 2002-11-21 23:50:00 UTC Re: Need indexing head software.... deanc500 2002-11-23 23:24:17 UTC Re: G201-IP deanc500 2002-11-27 16:45:38 UTC Re: G Code for 25 Pin D connector deanc500 2002-11-28 16:29:56 UTC Re: max. Servo motor voltage ?? deanc500 2002-11-28 20:41:58 UTC Re: First Timer - Please Help deanc500 2002-11-29 09:41:41 UTC Re: DC Brushless Motors and Drives deanc500 2002-11-30 19:55:04 UTC Re: Brushless Servo Drives - Non Step/Dir Input deanc500 2003-03-05 11:42:26 UTC Re: Pendant Design, was - Spindle Motor Control? deanc500 2003-03-21 19:02:45 UTC Re: Problem deanc500 2003-04-08 22:19:23 UTC Re: Parallel port Breakout Interface Box / Board deanc500 2003-04-10 00:01:09 UTC Re: Parallel port Breakout Interface Box / Board deanc500 2003-04-29 10:20:26 UTC Using belt drive on large machine - preliminary pictures deanc500 2003-04-29 11:03:08 UTC Re: Using belt drive on large machine - preliminary pictures deanc500 2003-04-29 11:37:54 UTC Re: Using belt drive on large machine - preliminary pictures deanc500 2003-04-30 06:23:05 UTC Re: Dirty Little Secrets (response) - solved deanc500 2003-04-30 06:45:40 UTC Re: Dirty Little Secrets (response) - solved deanc500 2003-04-30 07:06:10 UTC Re: Using belt drive on large machine - preliminary pictures deanc500 2003-04-30 07:14:39 UTC Re: Using belt drive on large machine - preliminary pictures - flat ? deanc500 2003-04-30 09:17:18 UTC Mill Video deanc500 2003-06-09 16:33:36 UTC Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed deanc500 2003-06-09 22:28:42 UTC Re: CNC Servo motor gear ratio: overheating. EMC step rate. Tablespeed deanc500 2003-07-08 09:09:35 UTC Re: Counterweighting the Z axis ?; Power off position holding ? deanc500 2003-07-08 10:07:55 UTC Re: Firm-name/address of driver I saw "here" deanc500 2003-07-09 06:56:12 UTC Re: Encoders deanc500 2003-09-11 07:31:56 UTC Re: Better servo performance: Ameteks at 60V, 80V ? deanc500 2003-10-15 12:56:56 UTC Timing belt driven router - updated photos deanc500 2003-12-29 14:52:05 UTC Re: Gecko 320 problem deanc500 2004-01-06 11:22:53 UTC Re: preloading ballscrews deanc500 2004-01-21 19:59:34 UTC Re: Looking for a link