Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
Posted by
Bob Simon
on 2003-09-16 13:10:30 UTC
At 04:24 PM 9/16/03 +0000, you wrote:
Make a flat sheet with a width of the circumference of the cylinder.
Cut a slot or an edge with a sketch of the flattened curve you want.
Sketch a line lengthwise across the middle of the part.
Add a sheet metal bend across the line with the radius of your cylinder.
You'll have to fudge a bit since the software won't let you make a perfect
part. you'll have to back the angle down to 359.9 degrees and fool around
with the radius a bit.
Good luck!
-Bob
>Thanks for the reply,Unfortunately it does only project. Try this;
>I had tried that before and it projects the curve on the face
>as opposed to wrapping the curve around the face.
>
>The difference between projection and wrapping is slight but
>important to what I am trying to do.
>
>I may be mistaken but it seems to me that the projection command does
>only projection, unless you know how to make it wrap around a
>cylinder.
Make a flat sheet with a width of the circumference of the cylinder.
Cut a slot or an edge with a sketch of the flattened curve you want.
Sketch a line lengthwise across the middle of the part.
Add a sheet metal bend across the line with the radius of your cylinder.
You'll have to fudge a bit since the software won't let you make a perfect
part. you'll have to back the angle down to 359.9 degrees and fool around
with the radius a bit.
Good luck!
-Bob
Discussion Thread
mjf462001
2003-09-15 19:58:16 UTC
Wrapping on a cylinder Solidworks?
Bob Simon
2003-09-16 05:53:49 UTC
Re: [CAD_CAM_EDM_DRO] Wrapping on a cylinder Solidworks?
mjf462001
2003-09-16 09:24:57 UTC
Re: Wrapping on a cylinder Solidworks?
Bob Simon
2003-09-16 13:10:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
mjf462001
2003-09-16 15:14:11 UTC
Re: Wrapping on a cylinder Solidworks?
rainnea
2003-09-16 15:26:37 UTC
Re: Wrapping on a cylinder Solidworks?
Carlos Guillermo
2003-09-16 16:56:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
Fred Smith
2003-09-16 17:12:26 UTC
Re: Wrapping on a cylinder Solidworks?
alenz2002
2003-09-16 21:50:21 UTC
Re: Wrapping on a cylinder Solidworks?
Thomas Fritz
2003-09-17 00:14:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
Matthew D. Armistead
2003-09-17 00:14:53 UTC
Drivers using the MC3479P?
Bob Simon
2003-09-17 06:30:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
m0nkey0ne
2003-09-17 21:50:19 UTC
Re: Wrapping on a cylinder Solidworks?
Chris Cowley
2003-09-17 23:44:13 UTC
Re: [CAD_CAM_EDM_DRO] Drivers using the MC3479P?
Jay Arnold
2003-09-17 23:45:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?
americo pacheco
2003-09-18 11:42:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Wrapping on a cylinder Solidworks?