CAD CAM EDM DRO - Yahoo Group Archive

Re: Capacitor safety questions

Posted by Torsten
on 2003-12-26 23:03:26 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
>
>
> volitan712003 wrote:
>
> >Hello,
> >
> >I just ordered a 12,000uF x 100V capacitor for my power supply. I
know
> >capacitors can be deadly but I have no concept of what a micro
farad
> >is. If this cap is fully charged, is this thing big enough to kill?
> >
> >
> At 100 V, if your fingers were wet or had cuts, and you jammed them
onto
> the terminals, yes, it could be fatal. This would be a pretty
unusual
> event.
> But, that's why people put bleeder resistors on them, so they
discharge in
> a short amount of time.
>

Jon, I have a very similar setup and got buzzed a few times and
like to find out more on the "bleeder resistors" you mensioned
my system retains power when unpluged for more then 24 hours and
I think this may be the answer to my problem.
What I am looking for is something that will drain power after
shutoff in about an hour or earlier so I can work on it.
Will this bleeder resistor reduce power output during normal
opperation?
What size partno. where to get and how should it be wired up.
Thanks for any info you could provide.

Discussion Thread

volitan712003 2003-12-26 18:29:06 UTC Capacitor safety questions bull2003winkle 2003-12-26 18:44:36 UTC Re: Capacitor safety questions Jon Elson 2003-12-26 22:12:35 UTC Re: [CAD_CAM_EDM_DRO] Capacitor safety questions wanliker@a... 2003-12-26 22:16:33 UTC Re: [CAD_CAM_EDM_DRO] Capacitor safety questions Torsten 2003-12-26 23:03:26 UTC Re: Capacitor safety questions turbulatordude 2003-12-27 05:19:38 UTC Re: Capacitor safety questions John Johnson 2003-12-27 06:45:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Capacitor safety questions volitan712003 2003-12-27 08:01:50 UTC Re: Capacitor safety questions ballendo 2003-12-27 08:27:21 UTC Re: Capacitor safety questions Richard L. Wurdack 2003-12-27 08:27:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Capacitor safety questions Robin Szemeti 2003-12-27 09:03:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Capacitor safety questions Richard 2003-12-27 10:27:29 UTC Re: Capacitor safety questions Mariss Freimanis 2003-12-27 12:03:02 UTC Re: Capacitor safety questions washcomp 2003-12-27 14:05:57 UTC Re: Capacitor safety questions OT Jon Elson 2003-12-27 22:07:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Capacitor safety questions bull2003winkle 2003-12-28 00:15:40 UTC Capacitor safety questions End of response ballendo 2003-12-28 10:31:45 UTC Re: Capacitor safety questions wanliker@a... 2003-12-28 11:36:05 UTC Re: [CAD_CAM_EDM_DRO] Capacitor safety questions End of response mayfieldtm 2003-12-29 07:41:43 UTC Re: Capacitor safety questions OT