RE: [CAD_CAM_EDM_DRO] Wire identification. hookup of Sanyo Super L servo? Help?
Posted by
Ed Gilbert
on 2004-02-21 18:33:21 UTC
Hi David,
Here is the encoder color code:
Red +5
Black 0 volts
Blue Channel A
White Channel B
Outputs are open collector so they require a pull up resistor to +5 if the
drive does not have one. Current should be limited to 10 milliamp maximum. 5
volts at 680 ohms is 7.35 milliamps.
Best,
Ed Gilbert
Gilbert Engineered Systems
632 Warrenton-Embro Road
Macon, NC 27551
252-257-0539
This message has been scanned for viruses and
dangerous content by NCOL.NET, and is believed to be clean.
Here is the encoder color code:
Red +5
Black 0 volts
Blue Channel A
White Channel B
Outputs are open collector so they require a pull up resistor to +5 if the
drive does not have one. Current should be limited to 10 milliamp maximum. 5
volts at 680 ohms is 7.35 milliamps.
Best,
Ed Gilbert
Gilbert Engineered Systems
632 Warrenton-Embro Road
Macon, NC 27551
252-257-0539
> -----Original Message------------------------------------------
> From: ibewgypsie [mailto:ibewgypsie@...]
> Sent: Saturday, February 21, 2004 12:32 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Wire identification. hookup of Sanyo Super L
> servo? Help?
>
> Howdy..
>
> I have 3 Sanyo Servo super L motors, Rutex drives to run them.
>
> Encoders on end, wires, Red, blue, black, white, shield
>
> If it was american, the red and black would be logical choices for
> power. Sometimes the japanese like blue, euro like white.. so?
>
> Going onto a gantry table if I ever get all the parts and loose ends
> together.
>
> David.
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
This message has been scanned for viruses and
dangerous content by NCOL.NET, and is believed to be clean.
Discussion Thread
ibewgypsie
2004-02-21 09:32:28 UTC
Wire identification. hookup of Sanyo Super L servo? Help?
Ed Gilbert
2004-02-21 18:33:21 UTC
RE: [CAD_CAM_EDM_DRO] Wire identification. hookup of Sanyo Super L servo? Help?
ibewgypsie
2004-02-22 13:45:43 UTC
Re: Wire identification. hookup of Sanyo Super L servo? Help?