CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] pic of smallish gear cut with my homebrew laser

on 2004-08-05 17:49:31 UTC
That is very cool.
----- Original Message -----
From: "skykotech" <rick@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, August 04, 2004 6:32 PM
Subject: [CAD_CAM_EDM_DRO] pic of smallish gear cut with my homebrew laser


> So after hooking up the z-axis direction sensing microcontroller to
> the laser, I drew a quickie gear in Rhino 3 and chose a 0.010 inch
> diameter endmill in VisualMill 5 using the 2D engraving mode. I set
> the laser to full power (about 16-17 watts).
>
> Here is what I ended up with (material 1/16" basswood):
>
> http://www.skyko.com/shizlaser/lasergear.JPG
>
> Total machining time was about 18 seconds at 60IPM feedrate!
>
> Not bad, but still not happy with my z-axis-laser-control solution :-/
>
> Rick
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>

Discussion Thread

skykotech 2004-08-04 16:33:02 UTC pic of smallish gear cut with my homebrew laser Robb Greathouse 2004-08-04 20:17:00 UTC Re: [CAD_CAM_EDM_DRO] pic of smallish gear cut with my homebrew laser Thierry Carel 2004-08-05 01:38:11 UTC Re: [CAD_CAM_EDM_DRO] pic of smallish gear cut with my homebrew laser skykotech 2004-08-05 09:10:44 UTC Re: pic of smallish gear cut with my homebrew laser Vince Negrete 2004-08-05 12:04:38 UTC Re: [CAD_CAM_EDM_DRO] Re: pic of smallish gear cut with my homebrew laser Tom Hubin 2004-08-05 12:29:37 UTC Re: [CAD_CAM_EDM_DRO] Re: pic of smallish gear cut with my homebrew laser Victor A. Estes 2004-08-05 17:49:31 UTC Re: [CAD_CAM_EDM_DRO] pic of smallish gear cut with my homebrew laser